--- a/arch/arm/mach-kirkwood/Kconfig +++ b/arch/arm/mach-kirkwood/Kconfig @@ -28,6 +28,9 @@ config TARGET_POGO_E02 config TARGET_POGOPLUGV4 bool "Pogoplug V4 Board" +config TARGET_DNS320L + bool "dns320l Board" + config TARGET_DNS325 bool "dns325 Board" @@ -93,6 +96,7 @@ source "board/Marvell/sheevaplug/Kconfig source "board/buffalo/lsxl/Kconfig" source "board/cloudengines/pogo_e02/Kconfig" source "board/cloudengines/pogoplugv4/Kconfig" +source "board/d-link/dns320l/Kconfig" source "board/d-link/dns325/Kconfig" source "board/iomega/iconnect/Kconfig" source "board/keymile/Kconfig" --- /dev/null +++ b/board/d-link/dns320l/dns320l.c @@ -0,0 +1,113 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2015 + * Gerald Kerma + * Tony Dinh + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include "dns320l.h" + +DECLARE_GLOBAL_DATA_PTR; + +int board_early_init_f(void) +{ + /* + * default gpio configuration + * There are maximum 64 gpios controlled through 2 sets of registers + * the below configuration configures mainly initial LED status + */ + mvebu_config_gpio(DNS320L_OE_VAL_LOW, DNS320L_OE_VAL_HIGH, + DNS320L_OE_LOW, DNS320L_OE_HIGH); + + /* (all LEDs & power off active high) */ + /* Multi-Purpose Pins Functionality configuration */ + static const u32 kwmpp_config[] = { + MPP0_NF_IO2, + MPP1_NF_IO3, + MPP2_NF_IO4, + MPP3_NF_IO5, + MPP4_NF_IO6, + MPP5_NF_IO7, + MPP6_SYSRST_OUTn, + MPP7_GPO, + MPP8_TW_SDA, + MPP9_TW_SCK, + MPP10_UART0_TXD, + MPP11_UART0_RXD, + MPP12_GPO, + MPP13_GPIO, + MPP14_GPIO, + MPP15_GPIO, + MPP16_GPIO, + MPP17_GPIO, + MPP18_NF_IO0, + MPP19_NF_IO1, + MPP20_SATA1_ACTn, /* sata1(left) status led */ + MPP21_SATA0_ACTn, /* sata0(right) status led */ + MPP22_GPIO, + MPP23_GPIO, + MPP24_GPIO, + MPP25_GPIO, + MPP26_GPIO, + MPP27_GPIO, + MPP28_GPIO, + MPP29_GPIO, + MPP30_GPIO, + MPP31_GPIO, + MPP32_GPIO, + 0 + }; + kirkwood_mpp_conf(kwmpp_config, NULL); + + kw_gpio_set_value(DNS320L_GPIO_SATA_EN , 1); + + return 0; +} + +int board_init(void) +{ + /* address of boot parameters */ + gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; + + return 0; +} + +#ifdef CONFIG_RESET_PHY_R +/* Configure and initialize PHY */ +void reset_phy(void) +{ + u16 reg; + u16 phyaddr; + char *name = "egiga0"; + + if (miiphy_set_current_dev(name)) + return; + + /* read PHY dev address */ + if (miiphy_read(name, 0xee, 0xee, (u16 *) &phyaddr)) { + printf("could not read PHY dev address\n"); + return; + } + + /* set RGMII delay */ + miiphy_write(name, phyaddr, MV88E1318_PGADR_REG, MV88E1318_MAC_CTRL_PG); + miiphy_read(name, phyaddr, MV88E1318_MAC_CTRL_REG, ®); + reg |= (MV88E1318_RGMII_RX_CTRL | MV88E1318_RGMII_TX_CTRL); + miiphy_write(name, phyaddr, MV88E1318_MAC_CTRL_REG, reg); + miiphy_write(name, phyaddr, MV88E1318_PGADR_REG, 0); + + /* reset PHY */ + if (miiphy_reset(name, phyaddr)) + return; + + printf("MV88E1318 PHY initialized on %s\n", name); +} +#endif /* CONFIG_RESET_PHY_R */ --- /dev/null +++ b/board/d-link/dns320l/dns320l.h @@ -0,0 +1,39 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) 2011 + * Stefan Herbrechtsmeier + * + * Based on Kirkwood support: + * (C) Copyright 2009 + * Marvell Semiconductor + * Written-by: Prafulla Wadaskar + */ + +#ifndef __DNS320L_H +#define __DNS320L_H + +/* GPIO configuration */ +#define DNS320L_GPIO_SATA_EN 24 +#define HDD_L_GREEN_LED (1 << 22) +#define HDD_R_GREEN_LED (1 << 23) +#define USB_BLUE_LED (1 << 25) +#define USB_ORANGE_LED (1 << 26) + +#define DNS320L_OE_LOW (~(HDD_L_GREEN_LED | HDD_R_GREEN_LED | \ + USB_BLUE_LED | USB_ORANGE_LED)) +#define DNS320L_OE_VAL_LOW (0) + +/* high GPIO's */ +#define WATCHDOG_SIGNAL (1 << 14) + +#define DNS320L_OE_HIGH (~(WATCHDOG_SIGNAL)) +#define DNS320L_OE_VAL_HIGH ((WATCHDOG_SIGNAL)) + +/* PHY related */ +#define MV88E1318_PGADR_REG 22 +#define MV88E1318_MAC_CTRL_PG 2 +#define MV88E1318_MAC_CTRL_REG 21 +#define MV88E1318_RGMII_TX_CTRL (1 << 4) +#define MV88E1318_RGMII_RX_CTRL (1 << 5) + +#endif /* __DNS320L_H */ --- /dev/null +++ b/board/d-link/dns320l/Kconfig @@ -0,0 +1,18 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (C) 2015 +# Gerald Kerma +# Tony Dinh + +if TARGET_DNS320L + +config SYS_BOARD + default "dns320l" + +config SYS_VENDOR + default "d-link" + +config SYS_CONFIG_NAME + default "dns320l" + +endif --- /dev/null +++ b/board/d-link/dns320l/kwbimage.cfg @@ -0,0 +1,41 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (C) 2015 +# Gerald Kerma +# Tony Dinh +# Refer to doc/README.kwbimage for more details about how-to +# configure and create kirkwood boot images. +# + +# Boot Media configurations +BOOT_FROM nand +NAND_ECC_MODE default +NAND_PAGE_SIZE 0x0800 + +# Configure RGMII-0 interface pad voltage to 1.8V +DATA 0xFFD100e0 0x1b1b1b9b + +DATA 0xFFD01400 0x43010c30 +DATA 0xFFD01404 0x39543000 +DATA 0xFFD01408 0x22125451 +DATA 0xFFD0140C 0x00000833 +DATA 0xFFD01410 0x0000000C +DATA 0xFFD01414 0x00000000 +DATA 0xFFD01418 0x00000000 +DATA 0xFFD0141C 0x00000652 +DATA 0xFFD01420 0x00000004 +DATA 0xFFD01424 0x0000F17F +DATA 0xFFD01428 0x00085520 +DATA 0xFFD0147c 0x00008552 +DATA 0xFFD01504 0x0FFFFFF1 +DATA 0xFFD01508 0x10000000 +DATA 0xFFD0150C 0x00000000 +DATA 0xFFD01514 0x00000000 +DATA 0xFFD0151C 0x00000000 +DATA 0xFFD01494 0x00010000 +DATA 0xFFD01498 0x00000000 +DATA 0xFFD0149C 0x0000E403 +DATA 0xFFD01480 0x00000001 +DATA 0xFFD20134 0x66666666 +DATA 0xFFD20138 0x66666666 +DATA 0x0 0x0 --- /dev/null +++ b/board/d-link/dns320l/MAINTAINERS @@ -0,0 +1,8 @@ +NSA310S BOARD +M: Gerald Kerma +M: Tony Dinh +M: Luka Perkov +S: Maintained +F: board/d-link/dns320l/ +F: include/configs/dns320l.h +F: configs/dns320l_defconfig --- /dev/null +++ b/board/d-link/dns320l/Makefile @@ -0,0 +1,7 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (C) 2015 +# Gerald Kerma +# Tony Dinh + +obj-y := dns320l.o --- /dev/null +++ b/configs/dns320l_defconfig @@ -0,0 +1,48 @@ +CONFIG_ARM=y +CONFIG_SYS_DCACHE_OFF=y +CONFIG_ARCH_CPU_INIT=y +CONFIG_KIRKWOOD=y +CONFIG_SYS_TEXT_BASE=0x600000 +CONFIG_TARGET_DNS320L=y +CONFIG_ENV_SIZE=0x20000 +CONFIG_ENV_OFFSET=0x100000 +CONFIG_NR_DRAM_BANKS=2 +CONFIG_BOOTDELAY=3 +CONFIG_USE_PREBOOT=y +# CONFIG_DISPLAY_BOARDINFO is not set +CONFIG_HUSH_PARSER=y +CONFIG_SYS_PROMPT="dns320l => " +CONFIG_CMD_BOOTZ=y +# CONFIG_CMD_FLASH is not set +CONFIG_CMD_IDE=y +CONFIG_CMD_NAND=y +CONFIG_CMD_USB=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_DHCP=y +CONFIG_CMD_MII=y +CONFIG_CMD_PING=y +CONFIG_CMD_EXT2=y +CONFIG_CMD_FAT=y +CONFIG_CMD_JFFS2=y +CONFIG_CMD_MTDPARTS=y +CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:0x100000@0x0(uboot),0x20000@0x100000(ubootenv),0x6de0000@0x120000(ubi),0xa00000@0x6f00000(mini),0x500000@0x7900000(config),0x200000@0x7e00000(my-dlink)" +CONFIG_CMD_UBI=y +CONFIG_ISO_PARTITION=y +CONFIG_ENV_IS_IN_NAND=y +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_MVSATA_IDE=y +# CONFIG_MMC is not set +CONFIG_MTD=y +CONFIG_MTD_RAW_NAND=y +CONFIG_MVGBE=y +CONFIG_MII=y +CONFIG_SYS_NS16550=y +CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_STORAGE=y +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_LZMA=y +CONFIG_LZO=y +CONFIG_OF_LIBFDT=y +CONFIG_NET_RANDOM_ETHADDR=y --- /dev/null +++ b/include/configs/dns320l.h @@ -0,0 +1,69 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) 2015 + * Gerald Kerma + * Tony Dinh + * Luka Perkov + */ + +#ifndef _CONFIG_DNS320L_H +#define _CONFIG_DNS320L_H + +/* high level configuration options */ +#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */ +#define CONFIG_KW88F6192 1 /* SOC Name */ +#define CONFIG_KW88F6702 1 /* SOC Name */ +#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ + +/* compression configuration */ +#define CONFIG_BZIP2 + +/* commands configuration */ + +/* + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros + */ +#include "mv-common.h" + +/* environment variables configuration */ + +/* default environment variables */ +#define CONFIG_BOOTCOMMAND \ + "ubi part ubi; " \ + "ubi read 0x800000 kernel; " \ + "bootm 0x800000" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "console=console=ttyS0,115200\0" \ + "mtdids=nand0=orion_nand\0" \ + "mtdparts="CONFIG_MTDPARTS_DEFAULT "\0" \ + "bootargs_root=ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs rw\0" + +/* Ethernet driver configuration */ +#ifdef CONFIG_CMD_NET +#define CONFIG_NETCONSOLE +#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ +#define CONFIG_PHY_BASE_ADR 1 +#define CONFIG_RESET_PHY_R +#endif /* CONFIG_CMD_NET */ + +/* SATA driver configuration */ +#ifdef CONFIG_IDE +#define __io +#define CONFIG_IDE_PREINIT +#define CONFIG_MVSATA_IDE_USE_PORT0 +#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET +#endif /* CONFIG_IDE */ + +/* + * Enable GPI0 support +*/ +#define CONFIG_KIRKWOOD_GPIO + +/* RTC driver configuration */ +#ifdef CONFIG_CMD_DATE +#define CONFIG_RTC_MV +#endif /* CONFIG_CMD_DATE */ + +#endif /* _CONFIG_DNS320L_H */