From 94800350cb8d2f29dda2206b5e9a3772024ee168 Mon Sep 17 00:00:00 2001 From: John Crispin Date: Thu, 7 Aug 2014 18:30:56 +0200 Subject: [PATCH 08/36] MIPS: lantiq: backport old timer code Signed-off-by: John Crispin --- arch/mips/include/asm/mach-lantiq/lantiq_timer.h | 155 ++++ arch/mips/lantiq/xway/Makefile | 2 +- arch/mips/lantiq/xway/timer.c | 845 ++++++++++++++++++++++ 3 files changed, 1001 insertions(+), 1 deletion(-) create mode 100644 arch/mips/include/asm/mach-lantiq/lantiq_timer.h create mode 100644 arch/mips/lantiq/xway/timer.c --- /dev/null +++ b/arch/mips/include/asm/mach-lantiq/lantiq_timer.h @@ -0,0 +1,155 @@ +#ifndef __DANUBE_GPTU_DEV_H__2005_07_26__10_19__ +#define __DANUBE_GPTU_DEV_H__2005_07_26__10_19__ + + +/****************************************************************************** + Copyright (c) 2002, Infineon Technologies. All rights reserved. + + No Warranty + Because the program is licensed free of charge, there is no warranty for + the program, to the extent permitted by applicable law. Except when + otherwise stated in writing the copyright holders and/or other parties + provide the program "as is" without warranty of any kind, either + expressed or implied, including, but not limited to, the implied + warranties of merchantability and fitness for a particular purpose. The + entire risk as to the quality and performance of the program is with + you. should the program prove defective, you assume the cost of all + necessary servicing, repair or correction. + + In no event unless required by applicable law or agreed to in writing + will any copyright holder, or any other party who may modify and/or + redistribute the program as permitted above, be liable to you for + damages, including any general, special, incidental or consequential + damages arising out of the use or inability to use the program + (including but not limited to loss of data or data being rendered + inaccurate or losses sustained by you or third parties or a failure of + the program to operate with any other programs), even if such holder or + other party has been advised of the possibility of such damages. +******************************************************************************/ + + +/* + * #################################### + * Definition + * #################################### + */ + +/* + * Available Timer/Counter Index + */ +#define TIMER(n, X) (n * 2 + (X ? 1 : 0)) +#define TIMER_ANY 0x00 +#define TIMER1A TIMER(1, 0) +#define TIMER1B TIMER(1, 1) +#define TIMER2A TIMER(2, 0) +#define TIMER2B TIMER(2, 1) +#define TIMER3A TIMER(3, 0) +#define TIMER3B TIMER(3, 1) + +/* + * Flag of Timer/Counter + * These flags specify the way in which timer is configured. + */ +/* Bit size of timer/counter. */ +#define TIMER_FLAG_16BIT 0x0000 +#define TIMER_FLAG_32BIT 0x0001 +/* Switch between timer and counter. */ +#define TIMER_FLAG_TIMER 0x0000 +#define TIMER_FLAG_COUNTER 0x0002 +/* Stop or continue when overflowing/underflowing. */ +#define TIMER_FLAG_ONCE 0x0000 +#define TIMER_FLAG_CYCLIC 0x0004 +/* Count up or counter down. */ +#define TIMER_FLAG_UP 0x0000 +#define TIMER_FLAG_DOWN 0x0008 +/* Count on specific level or edge. */ +#define TIMER_FLAG_HIGH_LEVEL_SENSITIVE 0x0000 +#define TIMER_FLAG_LOW_LEVEL_SENSITIVE 0x0040 +#define TIMER_FLAG_RISE_EDGE 0x0010 +#define TIMER_FLAG_FALL_EDGE 0x0020 +#define TIMER_FLAG_ANY_EDGE 0x0030 +/* Signal is syncronous to module clock or not. */ +#define TIMER_FLAG_UNSYNC 0x0000 +#define TIMER_FLAG_SYNC 0x0080 +/* Different interrupt handle type. */ +#define TIMER_FLAG_NO_HANDLE 0x0000 +#if defined(__KERNEL__) + #define TIMER_FLAG_CALLBACK_IN_IRQ 0x0100 +#endif // defined(__KERNEL__) +#define TIMER_FLAG_SIGNAL 0x0300 +/* Internal clock source or external clock source */ +#define TIMER_FLAG_INT_SRC 0x0000 +#define TIMER_FLAG_EXT_SRC 0x1000 + + +/* + * ioctl Command + */ +#define GPTU_REQUEST_TIMER 0x01 /* General method to setup timer/counter. */ +#define GPTU_FREE_TIMER 0x02 /* Free timer/counter. */ +#define GPTU_START_TIMER 0x03 /* Start or resume timer/counter. */ +#define GPTU_STOP_TIMER 0x04 /* Suspend timer/counter. */ +#define GPTU_GET_COUNT_VALUE 0x05 /* Get current count value. */ +#define GPTU_CALCULATE_DIVIDER 0x06 /* Calculate timer divider from given freq.*/ +#define GPTU_SET_TIMER 0x07 /* Simplified method to setup timer. */ +#define GPTU_SET_COUNTER 0x08 /* Simplified method to setup counter. */ + +/* + * Data Type Used to Call ioctl + */ +struct gptu_ioctl_param { + unsigned int timer; /* In command GPTU_REQUEST_TIMER, GPTU_SET_TIMER, and * + * GPTU_SET_COUNTER, this field is ID of expected * + * timer/counter. If it's zero, a timer/counter would * + * be dynamically allocated and ID would be stored in * + * this field. * + * In command GPTU_GET_COUNT_VALUE, this field is * + * ignored. * + * In other command, this field is ID of timer/counter * + * allocated. */ + unsigned int flag; /* In command GPTU_REQUEST_TIMER, GPTU_SET_TIMER, and * + * GPTU_SET_COUNTER, this field contains flags to * + * specify how to configure timer/counter. * + * In command GPTU_START_TIMER, zero indicate start * + * and non-zero indicate resume timer/counter. * + * In other command, this field is ignored. */ + unsigned long value; /* In command GPTU_REQUEST_TIMER, this field contains * + * init/reload value. * + * In command GPTU_SET_TIMER, this field contains * + * frequency (0.001Hz) of timer. * + * In command GPTU_GET_COUNT_VALUE, current count * + * value would be stored in this field. * + * In command GPTU_CALCULATE_DIVIDER, this field * + * contains frequency wanted, and after calculation, * + * divider would be stored in this field to overwrite * + * the frequency. * + * In other command, this field is ignored. */ + int pid; /* In command GPTU_REQUEST_TIMER and GPTU_SET_TIMER, * + * if signal is required, this field contains process * + * ID to which signal would be sent. * + * In other command, this field is ignored. */ + int sig; /* In command GPTU_REQUEST_TIMER and GPTU_SET_TIMER, * + * if signal is required, this field contains signal * + * number which would be sent. * + * In other command, this field is ignored. */ +}; + +/* + * #################################### + * Data Type + * #################################### + */ +typedef void (*timer_callback)(unsigned long arg); + +extern int lq_request_timer(unsigned int, unsigned int, unsigned long, unsigned long, unsigned long); +extern int lq_free_timer(unsigned int); +extern int lq_start_timer(unsigned int, int); +extern int lq_stop_timer(unsigned int); +extern int lq_reset_counter_flags(u32 timer, u32 flags); +extern int lq_get_count_value(unsigned int, unsigned long *); +extern u32 lq_cal_divider(unsigned long); +extern int lq_set_timer(unsigned int, unsigned int, int, int, unsigned int, unsigned long, unsigned long); +extern int lq_set_counter(unsigned int timer, unsigned int flag, + u32 reload, unsigned long arg1, unsigned long arg2); + +#endif /* __DANUBE_GPTU_DEV_H__2005_07_26__10_19__ */ --- a/arch/mips/lantiq/xway/Makefile +++ b/arch/mips/lantiq/xway/Makefile @@ -1,4 +1,10 @@ # SPDX-License-Identifier: GPL-2.0-only -obj-y := prom.o sysctrl.o clk.o dma.o gptu.o dcdc.o +obj-y := prom.o sysctrl.o clk.o dma.o dcdc.o + +ifdef CONFIG_SOC_AMAZON_SE +obj-y += gptu.o +else +obj-y += timer.o +endif obj-y += vmmc.o --- /dev/null +++ b/arch/mips/lantiq/xway/timer.c @@ -0,0 +1,887 @@ +#ifndef CONFIG_SOC_AMAZON_SE + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include + +#include +#include +#include "../clk.h" + +#include +#include +#include + +#define MAX_NUM_OF_32BIT_TIMER_BLOCKS 6 + +#ifdef TIMER1A +#define FIRST_TIMER TIMER1A +#else +#define FIRST_TIMER 2 +#endif + +/* + * GPTC divider is set or not. + */ +#define GPTU_CLC_RMC_IS_SET 0 + +/* + * Timer Interrupt (IRQ) + */ +/* Must be adjusted when ICU driver is available */ +#define TIMER_INTERRUPT (INT_NUM_IM3_IRL0 + 22) + +/* + * Bits Operation + */ +#define GET_BITS(x, msb, lsb) \ + (((x) & ((1 << ((msb) + 1)) - 1)) >> (lsb)) +#define SET_BITS(x, msb, lsb, value) \ + (((x) & ~(((1 << ((msb) + 1)) - 1) ^ ((1 << (lsb)) - 1))) | \ + (((value) & ((1 << (1 + (msb) - (lsb))) - 1)) << (lsb))) + +/* + * GPTU Register Mapping + */ +#define LQ_GPTU (KSEG1 + 0x1E100A00) +#define LQ_GPTU_CLC ((volatile u32 *)(LQ_GPTU + 0x0000)) +#define LQ_GPTU_ID ((volatile u32 *)(LQ_GPTU + 0x0008)) +#define LQ_GPTU_CON(n, X) ((volatile u32 *)(LQ_GPTU + 0x0010 + ((X) * 4) + ((n) - 1) * 0x0020)) /* X must be either A or B */ +#define LQ_GPTU_RUN(n, X) ((volatile u32 *)(LQ_GPTU + 0x0018 + ((X) * 4) + ((n) - 1) * 0x0020)) /* X must be either A or B */ +#define LQ_GPTU_RELOAD(n, X) ((volatile u32 *)(LQ_GPTU + 0x0020 + ((X) * 4) + ((n) - 1) * 0x0020)) /* X must be either A or B */ +#define LQ_GPTU_COUNT(n, X) ((volatile u32 *)(LQ_GPTU + 0x0028 + ((X) * 4) + ((n) - 1) * 0x0020)) /* X must be either A or B */ +#define LQ_GPTU_IRNEN ((volatile u32 *)(LQ_GPTU + 0x00F4)) +#define LQ_GPTU_IRNICR ((volatile u32 *)(LQ_GPTU + 0x00F8)) +#define LQ_GPTU_IRNCR ((volatile u32 *)(LQ_GPTU + 0x00FC)) + +/* + * Clock Control Register + */ +#define GPTU_CLC_SMC GET_BITS(*LQ_GPTU_CLC, 23, 16) +#define GPTU_CLC_RMC GET_BITS(*LQ_GPTU_CLC, 15, 8) +#define GPTU_CLC_FSOE (*LQ_GPTU_CLC & (1 << 5)) +#define GPTU_CLC_EDIS (*LQ_GPTU_CLC & (1 << 3)) +#define GPTU_CLC_SPEN (*LQ_GPTU_CLC & (1 << 2)) +#define GPTU_CLC_DISS (*LQ_GPTU_CLC & (1 << 1)) +#define GPTU_CLC_DISR (*LQ_GPTU_CLC & (1 << 0)) + +#define GPTU_CLC_SMC_SET(value) SET_BITS(0, 23, 16, (value)) +#define GPTU_CLC_RMC_SET(value) SET_BITS(0, 15, 8, (value)) +#define GPTU_CLC_FSOE_SET(value) ((value) ? (1 << 5) : 0) +#define GPTU_CLC_SBWE_SET(value) ((value) ? (1 << 4) : 0) +#define GPTU_CLC_EDIS_SET(value) ((value) ? (1 << 3) : 0) +#define GPTU_CLC_SPEN_SET(value) ((value) ? (1 << 2) : 0) +#define GPTU_CLC_DISR_SET(value) ((value) ? (1 << 0) : 0) + +/* + * ID Register + */ +#define GPTU_ID_ID GET_BITS(*LQ_GPTU_ID, 15, 8) +#define GPTU_ID_CFG GET_BITS(*LQ_GPTU_ID, 7, 5) +#define GPTU_ID_REV GET_BITS(*LQ_GPTU_ID, 4, 0) + +/* + * Control Register of Timer/Counter nX + * n is the index of block (1 based index) + * X is either A or B + */ +#define GPTU_CON_SRC_EG(n, X) (*LQ_GPTU_CON(n, X) & (1 << 10)) +#define GPTU_CON_SRC_EXT(n, X) (*LQ_GPTU_CON(n, X) & (1 << 9)) +#define GPTU_CON_SYNC(n, X) (*LQ_GPTU_CON(n, X) & (1 << 8)) +#define GPTU_CON_EDGE(n, X) GET_BITS(*LQ_GPTU_CON(n, X), 7, 6) +#define GPTU_CON_INV(n, X) (*LQ_GPTU_CON(n, X) & (1 << 5)) +#define GPTU_CON_EXT(n, X) (*LQ_GPTU_CON(n, A) & (1 << 4)) /* Timer/Counter B does not have this bit */ +#define GPTU_CON_STP(n, X) (*LQ_GPTU_CON(n, X) & (1 << 3)) +#define GPTU_CON_CNT(n, X) (*LQ_GPTU_CON(n, X) & (1 << 2)) +#define GPTU_CON_DIR(n, X) (*LQ_GPTU_CON(n, X) & (1 << 1)) +#define GPTU_CON_EN(n, X) (*LQ_GPTU_CON(n, X) & (1 << 0)) + +#define GPTU_CON_SRC_EG_SET(value) ((value) ? 0 : (1 << 10)) +#define GPTU_CON_SRC_EXT_SET(value) ((value) ? (1 << 9) : 0) +#define GPTU_CON_SYNC_SET(value) ((value) ? (1 << 8) : 0) +#define GPTU_CON_EDGE_SET(value) SET_BITS(0, 7, 6, (value)) +#define GPTU_CON_INV_SET(value) ((value) ? (1 << 5) : 0) +#define GPTU_CON_EXT_SET(value) ((value) ? (1 << 4) : 0) +#define GPTU_CON_STP_SET(value) ((value) ? (1 << 3) : 0) +#define GPTU_CON_CNT_SET(value) ((value) ? (1 << 2) : 0) +#define GPTU_CON_DIR_SET(value) ((value) ? (1 << 1) : 0) + +#define GPTU_RUN_RL_SET(value) ((value) ? (1 << 2) : 0) +#define GPTU_RUN_CEN_SET(value) ((value) ? (1 << 1) : 0) +#define GPTU_RUN_SEN_SET(value) ((value) ? (1 << 0) : 0) + +#define GPTU_IRNEN_TC_SET(n, X, value) ((value) ? (1 << (((n) - 1) * 2 + (X))) : 0) +#define GPTU_IRNCR_TC_SET(n, X, value) ((value) ? (1 << (((n) - 1) * 2 + (X))) : 0) + +#define TIMER_FLAG_MASK_SIZE(x) (x & 0x0001) +#define TIMER_FLAG_MASK_TYPE(x) (x & 0x0002) +#define TIMER_FLAG_MASK_STOP(x) (x & 0x0004) +#define TIMER_FLAG_MASK_DIR(x) (x & 0x0008) +#define TIMER_FLAG_NONE_EDGE 0x0000 +#define TIMER_FLAG_MASK_EDGE(x) (x & 0x0030) +#define TIMER_FLAG_REAL 0x0000 +#define TIMER_FLAG_INVERT 0x0040 +#define TIMER_FLAG_MASK_INVERT(x) (x & 0x0040) +#define TIMER_FLAG_MASK_TRIGGER(x) (x & 0x0070) +#define TIMER_FLAG_MASK_SYNC(x) (x & 0x0080) +#define TIMER_FLAG_CALLBACK_IN_HB 0x0200 +#define TIMER_FLAG_MASK_HANDLE(x) (x & 0x0300) +#define TIMER_FLAG_MASK_SRC(x) (x & 0x1000) + +struct timer_dev_timer { + unsigned int f_irq_on; + unsigned int irq; + unsigned int flag; + unsigned long arg1; + unsigned long arg2; +}; + +struct timer_dev { + struct mutex gptu_mutex; + unsigned int number_of_timers; + unsigned int occupation; + unsigned int f_gptu_on; + struct timer_dev_timer timer[MAX_NUM_OF_32BIT_TIMER_BLOCKS * 2]; +}; + + +unsigned int ltq_get_fpi_bus_clock(int fpi) { + struct clk *clk = clk_get_fpi(); + return clk_get_rate(clk); +} + + +static long gptu_ioctl(struct file *, unsigned int, unsigned long); +static int gptu_open(struct inode *, struct file *); +static int gptu_release(struct inode *, struct file *); + +static struct file_operations gptu_fops = { + .owner = THIS_MODULE, + .unlocked_ioctl = gptu_ioctl, + .open = gptu_open, + .release = gptu_release +}; + +static struct miscdevice gptu_miscdev = { + .minor = MISC_DYNAMIC_MINOR, + .name = "gptu", + .fops = &gptu_fops, +}; + +static struct timer_dev timer_dev; + +static irqreturn_t timer_irq_handler(int irq, void *p) +{ + unsigned int timer; + unsigned int flag; + struct timer_dev_timer *dev_timer = (struct timer_dev_timer *)p; + + timer = irq - TIMER_INTERRUPT; + if (timer < timer_dev.number_of_timers + && dev_timer == &timer_dev.timer[timer]) { + /* Clear interrupt. */ + ltq_w32(1 << timer, LQ_GPTU_IRNCR); + + /* Call user hanler or signal. */ + flag = dev_timer->flag; + if (!(timer & 0x01) + || TIMER_FLAG_MASK_SIZE(flag) == TIMER_FLAG_16BIT) { + /* 16-bit timer or timer A of 32-bit timer */ + switch (TIMER_FLAG_MASK_HANDLE(flag)) { + case TIMER_FLAG_CALLBACK_IN_IRQ: + case TIMER_FLAG_CALLBACK_IN_HB: + if (dev_timer->arg1) + (*(timer_callback)dev_timer->arg1)(dev_timer->arg2); + break; + case TIMER_FLAG_SIGNAL: + send_sig((int)dev_timer->arg2, (struct task_struct *)dev_timer->arg1, 0); + break; + } + } + } + return IRQ_HANDLED; +} + +static inline void lq_enable_gptu(void) +{ + struct clk *clk = clk_get_sys("1e100a00.gptu", NULL); + clk_enable(clk); + + //ltq_pmu_enable(PMU_GPT); + + /* Set divider as 1, disable write protection for SPEN, enable module. */ + *LQ_GPTU_CLC = + GPTU_CLC_SMC_SET(0x00) | + GPTU_CLC_RMC_SET(0x01) | + GPTU_CLC_FSOE_SET(0) | + GPTU_CLC_SBWE_SET(1) | + GPTU_CLC_EDIS_SET(0) | + GPTU_CLC_SPEN_SET(0) | + GPTU_CLC_DISR_SET(0); +} + +static inline void lq_disable_gptu(void) +{ + struct clk *clk = clk_get_sys("1e100a00.gptu", NULL); + ltq_w32(0x00, LQ_GPTU_IRNEN); + ltq_w32(0xfff, LQ_GPTU_IRNCR); + + /* Set divider as 0, enable write protection for SPEN, disable module. */ + *LQ_GPTU_CLC = + GPTU_CLC_SMC_SET(0x00) | + GPTU_CLC_RMC_SET(0x00) | + GPTU_CLC_FSOE_SET(0) | + GPTU_CLC_SBWE_SET(0) | + GPTU_CLC_EDIS_SET(0) | + GPTU_CLC_SPEN_SET(0) | + GPTU_CLC_DISR_SET(1); + + clk_enable(clk); +} + +int lq_request_timer(unsigned int timer, unsigned int flag, + unsigned long value, unsigned long arg1, unsigned long arg2) +{ + int ret = 0; + unsigned int con_reg, irnen_reg; + int n, X; + + if (timer >= FIRST_TIMER + timer_dev.number_of_timers) + return -EINVAL; + + printk(KERN_INFO "request_timer(%d, 0x%08X, %lu)...", + timer, flag, value); + + if (TIMER_FLAG_MASK_SIZE(flag) == TIMER_FLAG_16BIT) + value &= 0xFFFF; + else + timer &= ~0x01; + + mutex_lock(&timer_dev.gptu_mutex); + + /* + * Allocate timer. + */ + if (timer < FIRST_TIMER) { + unsigned int mask; + unsigned int shift; + /* This takes care of TIMER1B which is the only choice for Voice TAPI system */ + unsigned int offset = TIMER2A; + + /* + * Pick up a free timer. + */ + if (TIMER_FLAG_MASK_SIZE(flag) == TIMER_FLAG_16BIT) { + mask = 1 << offset; + shift = 1; + } else { + mask = 3 << offset; + shift = 2; + } + for (timer = offset; + timer < offset + timer_dev.number_of_timers; + timer += shift, mask <<= shift) + if (!(timer_dev.occupation & mask)) { + timer_dev.occupation |= mask; + break; + } + if (timer >= offset + timer_dev.number_of_timers) { + printk("failed![%d]\n", __LINE__); + mutex_unlock(&timer_dev.gptu_mutex); + return -EINVAL; + } else + ret = timer; + } else { + register unsigned int mask; + + /* + * Check if the requested timer is free. + */ + mask = (TIMER_FLAG_MASK_SIZE(flag) == TIMER_FLAG_16BIT ? 1 : 3) << timer; + if ((timer_dev.occupation & mask)) { + printk("failed![%d] mask %#x, timer_dev.occupation %#x\n", + __LINE__, mask, timer_dev.occupation); + mutex_unlock(&timer_dev.gptu_mutex); + return -EBUSY; + } else { + timer_dev.occupation |= mask; + ret = 0; + } + } + + /* + * Prepare control register value. + */ + switch (TIMER_FLAG_MASK_EDGE(flag)) { + default: + case TIMER_FLAG_NONE_EDGE: + con_reg = GPTU_CON_EDGE_SET(0x00); + break; + case TIMER_FLAG_RISE_EDGE: + con_reg = GPTU_CON_EDGE_SET(0x01); + break; + case TIMER_FLAG_FALL_EDGE: + con_reg = GPTU_CON_EDGE_SET(0x02); + break; + case TIMER_FLAG_ANY_EDGE: + con_reg = GPTU_CON_EDGE_SET(0x03); + break; + } + if (TIMER_FLAG_MASK_TYPE(flag) == TIMER_FLAG_TIMER) + con_reg |= + TIMER_FLAG_MASK_SRC(flag) == + TIMER_FLAG_EXT_SRC ? GPTU_CON_SRC_EXT_SET(1) : + GPTU_CON_SRC_EXT_SET(0); + else + con_reg |= + TIMER_FLAG_MASK_SRC(flag) == + TIMER_FLAG_EXT_SRC ? GPTU_CON_SRC_EG_SET(1) : + GPTU_CON_SRC_EG_SET(0); + con_reg |= + TIMER_FLAG_MASK_SYNC(flag) == + TIMER_FLAG_UNSYNC ? GPTU_CON_SYNC_SET(0) : + GPTU_CON_SYNC_SET(1); + con_reg |= + TIMER_FLAG_MASK_INVERT(flag) == + TIMER_FLAG_REAL ? GPTU_CON_INV_SET(0) : GPTU_CON_INV_SET(1); + con_reg |= + TIMER_FLAG_MASK_SIZE(flag) == + TIMER_FLAG_16BIT ? GPTU_CON_EXT_SET(0) : + GPTU_CON_EXT_SET(1); + con_reg |= + TIMER_FLAG_MASK_STOP(flag) == + TIMER_FLAG_ONCE ? GPTU_CON_STP_SET(1) : GPTU_CON_STP_SET(0); + con_reg |= + TIMER_FLAG_MASK_TYPE(flag) == + TIMER_FLAG_TIMER ? GPTU_CON_CNT_SET(0) : + GPTU_CON_CNT_SET(1); + con_reg |= + TIMER_FLAG_MASK_DIR(flag) == + TIMER_FLAG_UP ? GPTU_CON_DIR_SET(1) : GPTU_CON_DIR_SET(0); + + /* + * Fill up running data. + */ + timer_dev.timer[timer - FIRST_TIMER].flag = flag; + timer_dev.timer[timer - FIRST_TIMER].arg1 = arg1; + timer_dev.timer[timer - FIRST_TIMER].arg2 = arg2; + if (TIMER_FLAG_MASK_SIZE(flag) != TIMER_FLAG_16BIT) + timer_dev.timer[timer - FIRST_TIMER + 1].flag = flag; + + /* + * Enable GPTU module. + */ + if (!timer_dev.f_gptu_on) { + lq_enable_gptu(); + timer_dev.f_gptu_on = 1; + } + + /* + * Enable IRQ. + */ + if (TIMER_FLAG_MASK_HANDLE(flag) != TIMER_FLAG_NO_HANDLE) { + if (TIMER_FLAG_MASK_HANDLE(flag) == TIMER_FLAG_SIGNAL) + timer_dev.timer[timer - FIRST_TIMER].arg1 = + (unsigned long) find_task_by_vpid((int) arg1); + + irnen_reg = 1 << (timer - FIRST_TIMER); + + if (TIMER_FLAG_MASK_HANDLE(flag) == TIMER_FLAG_SIGNAL + || (TIMER_FLAG_MASK_HANDLE(flag) == + TIMER_FLAG_CALLBACK_IN_IRQ + && timer_dev.timer[timer - FIRST_TIMER].arg1)) { + enable_irq(timer_dev.timer[timer - FIRST_TIMER].irq); + timer_dev.timer[timer - FIRST_TIMER].f_irq_on = 1; + } + } else + irnen_reg = 0; + + /* + * Write config register, reload value and enable interrupt. + */ + n = timer >> 1; + X = timer & 0x01; + *LQ_GPTU_CON(n, X) = con_reg; + *LQ_GPTU_RELOAD(n, X) = value; + /* printk("reload value = %d\n", (u32)value); */ + *LQ_GPTU_IRNEN |= irnen_reg; + + mutex_unlock(&timer_dev.gptu_mutex); + printk("successful!\n"); + return ret; +} +EXPORT_SYMBOL(lq_request_timer); + +int lq_free_timer(unsigned int timer) +{ + unsigned int flag; + unsigned int mask; + int n, X; + + if (!timer_dev.f_gptu_on) + return -EINVAL; + + if (timer < FIRST_TIMER || timer >= FIRST_TIMER + timer_dev.number_of_timers) + return -EINVAL; + + mutex_lock(&timer_dev.gptu_mutex); + + flag = timer_dev.timer[timer - FIRST_TIMER].flag; + if (TIMER_FLAG_MASK_SIZE(flag) != TIMER_FLAG_16BIT) + timer &= ~0x01; + + mask = (TIMER_FLAG_MASK_SIZE(flag) == TIMER_FLAG_16BIT ? 1 : 3) << timer; + if (((timer_dev.occupation & mask) ^ mask)) { + mutex_unlock(&timer_dev.gptu_mutex); + return -EINVAL; + } + + n = timer >> 1; + X = timer & 0x01; + + if (GPTU_CON_EN(n, X)) + *LQ_GPTU_RUN(n, X) = GPTU_RUN_CEN_SET(1); + + *LQ_GPTU_IRNEN &= ~GPTU_IRNEN_TC_SET(n, X, 1); + *LQ_GPTU_IRNCR |= GPTU_IRNCR_TC_SET(n, X, 1); + + if (timer_dev.timer[timer - FIRST_TIMER].f_irq_on) { + disable_irq(timer_dev.timer[timer - FIRST_TIMER].irq); + timer_dev.timer[timer - FIRST_TIMER].f_irq_on = 0; + } + + timer_dev.occupation &= ~mask; + if (!timer_dev.occupation && timer_dev.f_gptu_on) { + lq_disable_gptu(); + timer_dev.f_gptu_on = 0; + } + + mutex_unlock(&timer_dev.gptu_mutex); + + return 0; +} +EXPORT_SYMBOL(lq_free_timer); + +int lq_start_timer(unsigned int timer, int is_resume) +{ + unsigned int flag; + unsigned int mask; + int n, X; + + if (!timer_dev.f_gptu_on) + return -EINVAL; + + if (timer < FIRST_TIMER || timer >= FIRST_TIMER + timer_dev.number_of_timers) + return -EINVAL; + + mutex_lock(&timer_dev.gptu_mutex); + + flag = timer_dev.timer[timer - FIRST_TIMER].flag; + if (TIMER_FLAG_MASK_SIZE(flag) != TIMER_FLAG_16BIT) + timer &= ~0x01; + + mask = (TIMER_FLAG_MASK_SIZE(flag) == + TIMER_FLAG_16BIT ? 1 : 3) << timer; + if (((timer_dev.occupation & mask) ^ mask)) { + mutex_unlock(&timer_dev.gptu_mutex); + return -EINVAL; + } + + n = timer >> 1; + X = timer & 0x01; + + *LQ_GPTU_RUN(n, X) = GPTU_RUN_RL_SET(!is_resume) | GPTU_RUN_SEN_SET(1); + + + mutex_unlock(&timer_dev.gptu_mutex); + + return 0; +} +EXPORT_SYMBOL(lq_start_timer); + +int lq_stop_timer(unsigned int timer) +{ + unsigned int flag; + unsigned int mask; + int n, X; + + if (!timer_dev.f_gptu_on) + return -EINVAL; + + if (timer < FIRST_TIMER + || timer >= FIRST_TIMER + timer_dev.number_of_timers) + return -EINVAL; + + mutex_lock(&timer_dev.gptu_mutex); + + flag = timer_dev.timer[timer - FIRST_TIMER].flag; + if (TIMER_FLAG_MASK_SIZE(flag) != TIMER_FLAG_16BIT) + timer &= ~0x01; + + mask = (TIMER_FLAG_MASK_SIZE(flag) == TIMER_FLAG_16BIT ? 1 : 3) << timer; + if (((timer_dev.occupation & mask) ^ mask)) { + mutex_unlock(&timer_dev.gptu_mutex); + return -EINVAL; + } + + n = timer >> 1; + X = timer & 0x01; + + *LQ_GPTU_RUN(n, X) = GPTU_RUN_CEN_SET(1); + + mutex_unlock(&timer_dev.gptu_mutex); + + return 0; +} +EXPORT_SYMBOL(lq_stop_timer); + +int lq_reset_counter_flags(u32 timer, u32 flags) +{ + unsigned int oflag; + unsigned int mask, con_reg; + int n, X; + + if (!timer_dev.f_gptu_on) + return -EINVAL; + + if (timer < FIRST_TIMER || timer >= FIRST_TIMER + timer_dev.number_of_timers) + return -EINVAL; + + mutex_lock(&timer_dev.gptu_mutex); + + oflag = timer_dev.timer[timer - FIRST_TIMER].flag; + if (TIMER_FLAG_MASK_SIZE(oflag) != TIMER_FLAG_16BIT) + timer &= ~0x01; + + mask = (TIMER_FLAG_MASK_SIZE(oflag) == TIMER_FLAG_16BIT ? 1 : 3) << timer; + if (((timer_dev.occupation & mask) ^ mask)) { + mutex_unlock(&timer_dev.gptu_mutex); + return -EINVAL; + } + + switch (TIMER_FLAG_MASK_EDGE(flags)) { + default: + case TIMER_FLAG_NONE_EDGE: + con_reg = GPTU_CON_EDGE_SET(0x00); + break; + case TIMER_FLAG_RISE_EDGE: + con_reg = GPTU_CON_EDGE_SET(0x01); + break; + case TIMER_FLAG_FALL_EDGE: + con_reg = GPTU_CON_EDGE_SET(0x02); + break; + case TIMER_FLAG_ANY_EDGE: + con_reg = GPTU_CON_EDGE_SET(0x03); + break; + } + if (TIMER_FLAG_MASK_TYPE(flags) == TIMER_FLAG_TIMER) + con_reg |= TIMER_FLAG_MASK_SRC(flags) == TIMER_FLAG_EXT_SRC ? GPTU_CON_SRC_EXT_SET(1) : GPTU_CON_SRC_EXT_SET(0); + else + con_reg |= TIMER_FLAG_MASK_SRC(flags) == TIMER_FLAG_EXT_SRC ? GPTU_CON_SRC_EG_SET(1) : GPTU_CON_SRC_EG_SET(0); + con_reg |= TIMER_FLAG_MASK_SYNC(flags) == TIMER_FLAG_UNSYNC ? GPTU_CON_SYNC_SET(0) : GPTU_CON_SYNC_SET(1); + con_reg |= TIMER_FLAG_MASK_INVERT(flags) == TIMER_FLAG_REAL ? GPTU_CON_INV_SET(0) : GPTU_CON_INV_SET(1); + con_reg |= TIMER_FLAG_MASK_SIZE(flags) == TIMER_FLAG_16BIT ? GPTU_CON_EXT_SET(0) : GPTU_CON_EXT_SET(1); + con_reg |= TIMER_FLAG_MASK_STOP(flags) == TIMER_FLAG_ONCE ? GPTU_CON_STP_SET(1) : GPTU_CON_STP_SET(0); + con_reg |= TIMER_FLAG_MASK_TYPE(flags) == TIMER_FLAG_TIMER ? GPTU_CON_CNT_SET(0) : GPTU_CON_CNT_SET(1); + con_reg |= TIMER_FLAG_MASK_DIR(flags) == TIMER_FLAG_UP ? GPTU_CON_DIR_SET(1) : GPTU_CON_DIR_SET(0); + + timer_dev.timer[timer - FIRST_TIMER].flag = flags; + if (TIMER_FLAG_MASK_SIZE(flags) != TIMER_FLAG_16BIT) + timer_dev.timer[timer - FIRST_TIMER + 1].flag = flags; + + n = timer >> 1; + X = timer & 0x01; + + *LQ_GPTU_CON(n, X) = con_reg; + smp_wmb(); + mutex_unlock(&timer_dev.gptu_mutex); + return 0; +} +EXPORT_SYMBOL(lq_reset_counter_flags); + +int lq_get_count_value(unsigned int timer, unsigned long *value) +{ + unsigned int flag; + unsigned int mask; + int n, X; + + if (!timer_dev.f_gptu_on) + return -EINVAL; + + if (timer < FIRST_TIMER + || timer >= FIRST_TIMER + timer_dev.number_of_timers) + return -EINVAL; + + mutex_lock(&timer_dev.gptu_mutex); + + flag = timer_dev.timer[timer - FIRST_TIMER].flag; + if (TIMER_FLAG_MASK_SIZE(flag) != TIMER_FLAG_16BIT) + timer &= ~0x01; + + mask = (TIMER_FLAG_MASK_SIZE(flag) == TIMER_FLAG_16BIT ? 1 : 3) << timer; + if (((timer_dev.occupation & mask) ^ mask)) { + mutex_unlock(&timer_dev.gptu_mutex); + return -EINVAL; + } + + n = timer >> 1; + X = timer & 0x01; + + *value = *LQ_GPTU_COUNT(n, X); + + + mutex_unlock(&timer_dev.gptu_mutex); + + return 0; +} +EXPORT_SYMBOL(lq_get_count_value); + +u32 lq_cal_divider(unsigned long freq) +{ + u64 module_freq, fpi = ltq_get_fpi_bus_clock(2); + u32 clock_divider = 1; + module_freq = fpi * 1000; + do_div(module_freq, clock_divider * freq); + return module_freq; +} +EXPORT_SYMBOL(lq_cal_divider); + +int lq_set_timer(unsigned int timer, unsigned int freq, int is_cyclic, + int is_ext_src, unsigned int handle_flag, unsigned long arg1, + unsigned long arg2) +{ + unsigned long divider; + unsigned int flag; + + divider = lq_cal_divider(freq); + if (divider == 0) + return -EINVAL; + flag = ((divider & ~0xFFFF) ? TIMER_FLAG_32BIT : TIMER_FLAG_16BIT) + | (is_cyclic ? TIMER_FLAG_CYCLIC : TIMER_FLAG_ONCE) + | (is_ext_src ? TIMER_FLAG_EXT_SRC : TIMER_FLAG_INT_SRC) + | TIMER_FLAG_TIMER | TIMER_FLAG_DOWN + | TIMER_FLAG_MASK_HANDLE(handle_flag); + + printk(KERN_INFO "lq_set_timer(%d, %d), divider = %lu\n", + timer, freq, divider); + return lq_request_timer(timer, flag, divider, arg1, arg2); +} +EXPORT_SYMBOL(lq_set_timer); + +int lq_set_counter(unsigned int timer, unsigned int flag, u32 reload, + unsigned long arg1, unsigned long arg2) +{ + printk(KERN_INFO "lq_set_counter(%d, %#x, %d)\n", timer, flag, reload); + return lq_request_timer(timer, flag, reload, arg1, arg2); +} +EXPORT_SYMBOL(lq_set_counter); + +static long gptu_ioctl(struct file *file, unsigned int cmd, + unsigned long arg) +{ + int ret; + struct gptu_ioctl_param param; + + if (!access_ok((void __user *)arg, sizeof(struct gptu_ioctl_param))) + return -EFAULT; + if (copy_from_user(¶m, (void __user *)arg, sizeof(param))) + return -EFAULT; + + if ((((cmd == GPTU_REQUEST_TIMER || cmd == GPTU_SET_TIMER + || GPTU_SET_COUNTER) && param.timer < 2) + || cmd == GPTU_GET_COUNT_VALUE || cmd == GPTU_CALCULATE_DIVIDER) + && !access_ok((void __user *)arg, + sizeof(struct gptu_ioctl_param))) + return -EFAULT; + + switch (cmd) { + case GPTU_REQUEST_TIMER: + ret = lq_request_timer(param.timer, param.flag, param.value, + (unsigned long) param.pid, + (unsigned long) param.sig); + if (ret > 0) { + if (copy_to_user(&((struct gptu_ioctl_param *) arg)-> + timer, &ret, sizeof(&ret))) + ret = -EFAULT; + else + ret = 0; + } + break; + case GPTU_FREE_TIMER: + ret = lq_free_timer(param.timer); + break; + case GPTU_START_TIMER: + ret = lq_start_timer(param.timer, param.flag); + break; + case GPTU_STOP_TIMER: + ret = lq_stop_timer(param.timer); + break; + case GPTU_GET_COUNT_VALUE: + ret = lq_get_count_value(param.timer, ¶m.value); + if (!ret && copy_to_user(&((struct gptu_ioctl_param *) arg)-> + value, ¶m.value,sizeof(param.value))) + ret = -EFAULT; + break; + case GPTU_CALCULATE_DIVIDER: + param.value = lq_cal_divider(param.value); + if (param.value == 0) + ret = -EINVAL; + else if (copy_to_user(&((struct gptu_ioctl_param *) arg)-> + value, ¶m.value, + sizeof(param.value))) + ret = -EFAULT; + else + ret = 0; + break; + case GPTU_SET_TIMER: + ret = lq_set_timer(param.timer, param.value, + TIMER_FLAG_MASK_STOP(param.flag) != + TIMER_FLAG_ONCE ? 1 : 0, + TIMER_FLAG_MASK_SRC(param.flag) == + TIMER_FLAG_EXT_SRC ? 1 : 0, + TIMER_FLAG_MASK_HANDLE(param.flag) == + TIMER_FLAG_SIGNAL ? TIMER_FLAG_SIGNAL : + TIMER_FLAG_NO_HANDLE, + (unsigned long) param.pid, + (unsigned long) param.sig); + if (ret > 0) { + if (copy_to_user(&((struct gptu_ioctl_param *) arg)-> + timer, &ret, sizeof(&ret))) + ret = -EFAULT; + else + ret = 0; + } + break; + case GPTU_SET_COUNTER: + lq_set_counter(param.timer, param.flag, param.value, 0, 0); + if (ret > 0) { + if (copy_to_user(&((struct gptu_ioctl_param *) arg)-> + timer, &ret, sizeof(&ret))) + ret = -EFAULT; + else + ret = 0; + } + break; + default: + ret = -ENOTTY; + } + + return ret; +} + +static int gptu_open(struct inode *inode, struct file *file) +{ + return 0; +} + +static int gptu_release(struct inode *inode, struct file *file) +{ + return 0; +} + +static int gptu_probe(struct platform_device *pdev) +{ + int ret; + int i; + + ltq_w32(0, LQ_GPTU_IRNEN); + ltq_w32(0xfff, LQ_GPTU_IRNCR); + + memset(&timer_dev, 0, sizeof(timer_dev)); + mutex_init(&timer_dev.gptu_mutex); + + lq_enable_gptu(); + timer_dev.number_of_timers = GPTU_ID_CFG * 2; + lq_disable_gptu(); + if (timer_dev.number_of_timers > MAX_NUM_OF_32BIT_TIMER_BLOCKS * 2) + timer_dev.number_of_timers = MAX_NUM_OF_32BIT_TIMER_BLOCKS * 2; + printk(KERN_INFO "gptu: totally %d 16-bit timers/counters\n", timer_dev.number_of_timers); + + ret = misc_register(&gptu_miscdev); + if (ret) { + printk(KERN_ERR "gptu: can't misc_register, get error %d\n", -ret); + return ret; + } else { + printk(KERN_INFO "gptu: misc_register on minor %d\n", gptu_miscdev.minor); + } + + for (i = 0; i < timer_dev.number_of_timers; i++) { + int irq = platform_get_irq(pdev, i); + if (irq < 0) { + printk(KERN_ERR "gptu: failed in getting irq (%d), get error %d\n", i, irq); + for (i--; i >= 0; i--) + free_irq(timer_dev.timer[i].irq, &timer_dev.timer[i]); + misc_deregister(&gptu_miscdev); + return irq; + } + + ret = request_irq(irq, timer_irq_handler, IRQF_TIMER, gptu_miscdev.name, &timer_dev.timer[i]); + if (ret) { + printk(KERN_ERR "gptu: failed in requesting irq (%d), get error %d\n", i, -ret); + for (i--; i >= 0; i--) + free_irq(timer_dev.timer[i].irq, &timer_dev.timer[i]); + misc_deregister(&gptu_miscdev); + return ret; + } else { + timer_dev.timer[i].irq = irq; + disable_irq(timer_dev.timer[i].irq); + printk(KERN_INFO "gptu: succeeded to request irq %d\n", timer_dev.timer[i].irq); + } + } + + return 0; +} + +static const struct of_device_id gptu_match[] = { + { .compatible = "lantiq,gptu-xway" }, + {}, +}; +MODULE_DEVICE_TABLE(of, gptu_match); + +static struct platform_driver gptu_driver = { + .probe = gptu_probe, + .driver = { + .name = "gptu-xway", + .owner = THIS_MODULE, + .of_match_table = gptu_match, + }, +}; + +int __init lq_gptu_init(void) +{ + int ret = platform_driver_register(&gptu_driver); + + if (ret) + pr_info("gptu: Error registering platform driver\n"); + return ret; +} + +void __exit lq_gptu_exit(void) +{ + unsigned int i; + + for (i = 0; i < timer_dev.number_of_timers; i++) { + if (timer_dev.timer[i].f_irq_on) + disable_irq(timer_dev.timer[i].irq); + free_irq(timer_dev.timer[i].irq, &timer_dev.timer[i]); + } + lq_disable_gptu(); + misc_deregister(&gptu_miscdev); +} + +module_init(lq_gptu_init); +module_exit(lq_gptu_exit); + +#endif