menuconfig MTD_SPI_NOR
	tristate "SPI-NOR device support"
	depends on MTD
	help
	  This is the framework for the SPI NOR which can be used by the SPI
	  device drivers and the SPI-NOR device driver.

if MTD_SPI_NOR

config MTD_MT81xx_NOR
	tristate "Mediatek MT81xx SPI NOR flash controller"
	depends on HAS_IOMEM
	help
	  This enables access to SPI NOR flash, using MT81xx SPI NOR flash
	  controller. This controller does not support generic SPI BUS, it only
	  supports SPI NOR Flash.

config MTD_SPI_NOR_USE_4K_SECTORS
	bool "Use small 4096 B erase sectors"
	default y
	help
	  Many flash memories support erasing small (4096 B) sectors. Depending
	  on the usage this feature may provide performance gain in comparison
	  to erasing whole blocks (32/64 KiB).
	  Changing a small part of the flash's contents is usually faster with
	  small sectors. On the other hand erasing should be faster when using
	  64 KiB block instead of 16 × 4 KiB sectors.

	  Please note that some tools/drivers/filesystems may not work with
	  4096 B erase size (e.g. UBIFS requires 15 KiB as a minimum).

config SPI_ASPEED_SMC
	tristate "Aspeed flash controllers in SPI mode"
	depends on ARCH_ASPEED || COMPILE_TEST
	depends on HAS_IOMEM && OF
	help
	  This enables support for the Firmware Memory controller (FMC)
	  in the Aspeed AST2500/AST2400 SoCs when attached to SPI NOR chips,
	  and support for the SPI flash memory controller (SPI) for
	  the host firmware. The implementation only supports SPI NOR.

config MTD_SPI_NOR_USE_4K_SECTORS_LIMIT
	int "Maximum flash chip size to use 4K sectors on (in KiB)"
	depends on MTD_SPI_NOR_USE_4K_SECTORS
	default "4096"
	help
	  There are many flash chips that support 4K sectors, but are so large
	  that using them significantly slows down writing large amounts of
	  data or using a writable filesystem.
	  Any flash chip larger than the size specified in this option will
	  not use 4K sectors.

config SPI_ATMEL_QUADSPI
	tristate "Atmel Quad SPI Controller"
	depends on ARCH_AT91 || (ARM && COMPILE_TEST && !ARCH_EBSA110)
	depends on OF && HAS_IOMEM
	help
	  This enables support for the Quad SPI controller in master mode.
	  This driver does not support generic SPI. The implementation only
	  supports SPI NOR.

config SPI_CADENCE_QUADSPI
	tristate "Cadence Quad SPI controller"
	depends on OF && (ARM || COMPILE_TEST)
	help
	  Enable support for the Cadence Quad SPI Flash controller.

	  Cadence QSPI is a specialized controller for connecting an SPI
	  Flash over 1/2/4-bit wide bus. Enable this option if you have a
	  device with a Cadence QSPI controller and want to access the
	  Flash as an MTD device.

config SPI_FSL_QUADSPI
	tristate "Freescale Quad SPI controller"
	depends on ARCH_MXC || SOC_LS1021A || ARCH_LAYERSCAPE || COMPILE_TEST
	depends on HAS_IOMEM
	help
	  This enables support for the Quad SPI controller in master mode.
	  This controller does not support generic SPI. It only supports
	  SPI NOR.

config SPI_HISI_SFC
	tristate "Hisilicon SPI-NOR Flash Controller(SFC)"
	depends on ARCH_HISI || COMPILE_TEST
	depends on HAS_IOMEM && HAS_DMA
	help
	  This enables support for hisilicon SPI-NOR flash controller.

config SPI_NXP_SPIFI
	tristate "NXP SPI Flash Interface (SPIFI)"
	depends on OF && (ARCH_LPC18XX || COMPILE_TEST)
	depends on HAS_IOMEM
	help
	  Enable support for the NXP LPC SPI Flash Interface controller.

	  SPIFI is a specialized controller for connecting serial SPI
	  Flash. Enable this option if you have a device with a SPIFI
	  controller and want to access the Flash as a mtd device.

config SPI_INTEL_SPI
	tristate

config SPI_INTEL_SPI_PCI
	tristate "Intel PCH/PCU SPI flash PCI driver" if EXPERT
	depends on X86 && PCI
	select SPI_INTEL_SPI
	help
	  This enables PCI support for the Intel PCH/PCU SPI controller in
	  master mode. This controller is present in modern Intel hardware
	  and is used to hold BIOS and other persistent settings. Using
	  this driver it is possible to upgrade BIOS directly from Linux.

	  Say N here unless you know what you are doing. Overwriting the
	  SPI flash may render the system unbootable.

	  To compile this driver as a module, choose M here: the module
	  will be called intel-spi-pci.

config SPI_INTEL_SPI_PLATFORM
	tristate "Intel PCH/PCU SPI flash platform driver" if EXPERT
	depends on X86
	select SPI_INTEL_SPI
	help
	  This enables platform support for the Intel PCH/PCU SPI
	  controller in master mode. This controller is present in modern
	  Intel hardware and is used to hold BIOS and other persistent
	  settings. Using this driver it is possible to upgrade BIOS
	  directly from Linux.

	  Say N here unless you know what you are doing. Overwriting the
	  SPI flash may render the system unbootable.

	  To compile this driver as a module, choose M here: the module
	  will be called intel-spi-platform.

config SPI_STM32_QUADSPI
	tristate "STM32 Quad SPI controller"
	depends on ARCH_STM32 || COMPILE_TEST
	help
	  This enables support for the STM32 Quad SPI controller.
	  We only connect the NOR to this controller.

endif # MTD_SPI_NOR