From a2e1ba275eae96a8171deb19e9c7c2f5978fee7b Mon Sep 17 00:00:00 2001 From: Daniel Golle Date: Fri, 4 Oct 2024 17:18:16 +0100 Subject: [PATCH] net: phy: aquantia: allow forcing order of MDI pairs Despite supporting Auto MDI-X, it looks like Aquantia only supports swapping pair (1,2) with pair (3,6) like it used to be for MDI-X on 100MBit/s networks. When all 4 pairs are in use (for 1000MBit/s or faster) the link does not come up with pair order is not configured correctly, either using MDI_CFG pin or using the "PMA Receive Reserved Vendor Provisioning 1" register. Normally, the order of MDI pairs being either ABCD or DCBA is configured by pulling the MDI_CFG pin. However, some hardware designs require overriding the value configured by that bootstrap pin. The PHY allows doing that by setting a bit in "PMA Receive Reserved Vendor Provisioning 1" register which allows ignoring the state of the MDI_CFG pin and another bit configuring whether the order of MDI pairs should be normal (ABCD) or reverse (DCBA). Pair polarity is not affected and remains identical in both settings. Introduce property "marvell,mdi-cfg-order" which allows forcing either normal or reverse order of the MDI pairs from DT. If the property isn't present, the behavior is unchanged and MDI pair order configuration is untouched (ie. either the result of MDI_CFG pin pull-up/pull-down, or pair order override already configured by the bootloader before Linux is started). Forcing normal pair order is required on the Adtran SDG-8733A Wi-Fi 7 residential gateway. Signed-off-by: Daniel Golle Reviewed-by: Andrew Lunn Link: https://patch.msgid.link/9ed760ff87d5fc456f31e407ead548bbb754497d.1728058550.git.daniel@makrotopia.org Signed-off-by: Jakub Kicinski --- drivers/net/phy/aquantia/aquantia_main.c | 33 ++++++++++++++++++++++++ 1 file changed, 33 insertions(+) --- a/drivers/net/phy/aquantia/aquantia_main.c +++ b/drivers/net/phy/aquantia/aquantia_main.c @@ -11,6 +11,7 @@ #include #include #include +#include #include #include "aquantia.h" @@ -70,6 +71,11 @@ #define MDIO_AN_TX_VEND_INT_MASK2 0xd401 #define MDIO_AN_TX_VEND_INT_MASK2_LINK BIT(0) +#define PMAPMD_RSVD_VEND_PROV 0xe400 +#define PMAPMD_RSVD_VEND_PROV_MDI_CONF GENMASK(1, 0) +#define PMAPMD_RSVD_VEND_PROV_MDI_REVERSE BIT(0) +#define PMAPMD_RSVD_VEND_PROV_MDI_FORCE BIT(1) + #define MDIO_AN_RX_LP_STAT1 0xe820 #define MDIO_AN_RX_LP_STAT1_1000BASET_FULL BIT(15) #define MDIO_AN_RX_LP_STAT1_1000BASET_HALF BIT(14) @@ -497,6 +503,29 @@ static int aqr107_wait_processor_intensi return 0; } +static int aqr107_config_mdi(struct phy_device *phydev) +{ + struct device_node *np = phydev->mdio.dev.of_node; + u32 mdi_conf; + int ret; + + ret = of_property_read_u32(np, "marvell,mdi-cfg-order", &mdi_conf); + + /* Do nothing in case property "marvell,mdi-cfg-order" is not present */ + if (ret == -ENOENT) + return 0; + + if (ret) + return ret; + + if (mdi_conf & ~PMAPMD_RSVD_VEND_PROV_MDI_REVERSE) + return -EINVAL; + + return phy_modify_mmd(phydev, MDIO_MMD_PMAPMD, PMAPMD_RSVD_VEND_PROV, + PMAPMD_RSVD_VEND_PROV_MDI_CONF, + mdi_conf | PMAPMD_RSVD_VEND_PROV_MDI_FORCE); +} + static int aqr107_config_init(struct phy_device *phydev) { struct aqr107_priv *priv = phydev->priv; @@ -535,6 +564,10 @@ static int aqr107_config_init(struct phy if (ret) return ret; + ret = aqr107_config_mdi(phydev); + if (ret) + return ret; + /* Restore LED polarity state after reset */ for_each_set_bit(led_active_low, &priv->leds_active_low, AQR_MAX_LEDS) { ret = aqr_phy_led_active_low_set(phydev, led_active_low, true);