/* SPDX-License-Identifier: GPL-2.0-or-later */ /* * ahci.h - Common AHCI SATA definitions and declarations * * Maintained by: Tejun Heo * Please ALWAYS copy linux-ide@vger.kernel.org * on emails. * * Copyright 2004-2005 Red Hat, Inc. * * libata documentation is available via 'make {ps|pdf}docs', * as Documentation/driver-api/libata.rst * * AHCI hardware documentation: * http://www.intel.com/technology/serialata/pdf/rev1_0.pdf * http://www.intel.com/technology/serialata/pdf/rev1_1.pdf */ #ifndef _AHCI_H #define _AHCI_H #include #include #include #include #include #include /* Enclosure Management Control */ #define EM_CTRL_MSG_TYPE 0x000f0000 /* Enclosure Management LED Message Type */ #define EM_MSG_LED_HBA_PORT 0x0000000f #define EM_MSG_LED_PMP_SLOT 0x0000ff00 #define EM_MSG_LED_VALUE 0xffff0000 #define EM_MSG_LED_VALUE_ACTIVITY 0x00070000 #define EM_MSG_LED_VALUE_OFF 0xfff80000 #define EM_MSG_LED_VALUE_ON 0x00010000 enum { AHCI_MAX_PORTS = 32, AHCI_MAX_SG = 168, /* hardware max is 64K */ AHCI_DMA_BOUNDARY = 0xffffffff, AHCI_MAX_CMDS = 32, AHCI_CMD_SZ = 32, AHCI_CMD_SLOT_SZ = AHCI_MAX_CMDS * AHCI_CMD_SZ, AHCI_RX_FIS_SZ = 256, AHCI_CMD_TBL_CDB = 0x40, AHCI_CMD_TBL_HDR_SZ = 0x80, AHCI_CMD_TBL_SZ = AHCI_CMD_TBL_HDR_SZ + (AHCI_MAX_SG * 16), AHCI_CMD_TBL_AR_SZ = AHCI_CMD_TBL_SZ * AHCI_MAX_CMDS, AHCI_PORT_PRIV_DMA_SZ = AHCI_CMD_SLOT_SZ + AHCI_CMD_TBL_AR_SZ + AHCI_RX_FIS_SZ, AHCI_PORT_PRIV_FBS_DMA_SZ = AHCI_CMD_SLOT_SZ + AHCI_CMD_TBL_AR_SZ + (AHCI_RX_FIS_SZ * 16), AHCI_IRQ_ON_SG = BIT(31), AHCI_CMD_ATAPI = BIT(5), AHCI_CMD_WRITE = BIT(6), AHCI_CMD_PREFETCH = BIT(7), AHCI_CMD_RESET = BIT(8), AHCI_CMD_CLR_BUSY = BIT(10), RX_FIS_PIO_SETUP = 0x20, /* offset of PIO Setup FIS data */ RX_FIS_D2H_REG = 0x40, /* offset of D2H Register FIS data */ RX_FIS_SDB = 0x58, /* offset of SDB FIS data */ RX_FIS_UNK = 0x60, /* offset of Unknown FIS data */ /* global controller registers */ HOST_CAP = 0x00, /* host capabilities */ HOST_CTL = 0x04, /* global host control */ HOST_IRQ_STAT = 0x08, /* interrupt status */ HOST_PORTS_IMPL = 0x0c, /* bitmap of implemented ports */ HOST_VERSION = 0x10, /* AHCI spec. version compliancy */ HOST_EM_LOC = 0x1c, /* Enclosure Management location */ HOST_EM_CTL = 0x20, /* Enclosure Management Control */ HOST_CAP2 = 0x24, /* host capabilities, extended */ /* HOST_CTL bits */ HOST_RESET = BIT(0), /* reset controller; self-clear */ HOST_IRQ_EN = BIT(1), /* global IRQ enable */ HOST_MRSM = BIT(2), /* MSI Revert to Single Message */ HOST_AHCI_EN = BIT(31), /* AHCI enabled */ /* HOST_CAP bits */ HOST_CAP_SXS = BIT(5), /* Supports External SATA */ HOST_CAP_EMS = BIT(6), /* Enclosure Management support */ HOST_CAP_CCC = BIT(7), /* Command Completion Coalescing */ HOST_CAP_PART = BIT(13), /* Partial state capable */ HOST_CAP_SSC = BIT(14), /* Slumber state capable */ HOST_CAP_PIO_MULTI = BIT(15), /* PIO multiple DRQ support */ HOST_CAP_FBS = BIT(16), /* FIS-based switching support */ HOST_CAP_PMP = BIT(17), /* Port Multiplier support */ HOST_CAP_ONLY = BIT(18), /* Supports AHCI mode only */ HOST_CAP_CLO = BIT(24), /* Command List Override support */ HOST_CAP_LED = BIT(25), /* Supports activity LED */ HOST_CAP_ALPM = BIT(26), /* Aggressive Link PM support */ HOST_CAP_SSS = BIT(27), /* Staggered Spin-up */ HOST_CAP_MPS = BIT(28), /* Mechanical presence switch */ HOST_CAP_SNTF = BIT(29), /* SNotification register */ HOST_CAP_NCQ = BIT(30), /* Native Command Queueing */ HOST_CAP_64 = BIT(31), /* PCI DAC (64-bit DMA) support */ /* HOST_CAP2 bits */ HOST_CAP2_BOH = BIT(0), /* BIOS/OS handoff supported */ HOST_CAP2_NVMHCI = BIT(1), /* NVMHCI supported */ HOST_CAP2_APST = BIT(2), /* Automatic partial to slumber */ HOST_CAP2_SDS = BIT(3), /* Support device sleep */ HOST_CAP2_SADM = BIT(4), /* Support aggressive DevSlp */ HOST_CAP2_DESO = BIT(5), /* DevSlp from slumber only */ /* registers for each SATA port */ PORT_LST_ADDR = 0x00, /* command list DMA addr */ PORT_LST_ADDR_HI = 0x04, /* command list DMA addr hi */ PORT_FIS_ADDR = 0x08, /* FIS rx buf addr */ PORT_FIS_ADDR_HI = 0x0c, /* FIS rx buf addr hi */ PORT_IRQ_STAT = 0x10, /* interrupt status */ PORT_IRQ_MASK = 0x14, /* interrupt enable/disable mask */ PORT_CMD = 0x18, /* port command */ PORT_TFDATA = 0x20, /* taskfile data */ PORT_SIG = 0x24, /* device TF signature */ PORT_CMD_ISSUE = 0x38, /* command issue */ PORT_SCR_STAT = 0x28, /* SATA phy register: SStatus */ PORT_SCR_CTL = 0x2c, /* SATA phy register: SControl */ PORT_SCR_ERR = 0x30, /* SATA phy register: SError */ PORT_SCR_ACT = 0x34, /* SATA phy register: SActive */ PORT_SCR_NTF = 0x3c, /* SATA phy register: SNotification */ PORT_FBS = 0x40, /* FIS-based Switching */ PORT_DEVSLP = 0x44, /* device sleep */ /* PORT_IRQ_{STAT,MASK} bits */ PORT_IRQ_COLD_PRES = BIT(31), /* cold presence detect */ PORT_IRQ_TF_ERR = BIT(30), /* task file error */ PORT_IRQ_HBUS_ERR = BIT(29), /* host bus fatal error */ PORT_IRQ_HBUS_DATA_ERR = BIT(28), /* host bus data error */ PORT_IRQ_IF_ERR = BIT(27), /* interface fatal error */ PORT_IRQ_IF_NONFATAL = BIT(26), /* interface non-fatal error */ PORT_IRQ_OVERFLOW = BIT(24), /* xfer exhausted available S/G */ PORT_IRQ_BAD_PMP = BIT(23), /* incorrect port multiplier */ PORT_IRQ_PHYRDY = BIT(22), /* PhyRdy changed */ PORT_IRQ_DEV_ILCK = BIT(7), /* device interlock */ PORT_IRQ_CONNECT = BIT(6), /* port connect change status */ PORT_IRQ_SG_DONE = BIT(5), /* descriptor processed */ PORT_IRQ_UNK_FIS = BIT(4), /* unknown FIS rx'd */ PORT_IRQ_SDB_FIS = BIT(3), /* Set Device Bits FIS rx'd */ PORT_IRQ_DMAS_FIS = BIT(2), /* DMA Setup FIS rx'd */ PORT_IRQ_PIOS_FIS = BIT(1), /* PIO Setup FIS rx'd */ PORT_IRQ_D2H_REG_FIS = BIT(0), /* D2H Register FIS rx'd */ PORT_IRQ_FREEZE = PORT_IRQ_HBUS_ERR | PORT_IRQ_IF_ERR | PORT_IRQ_CONNECT | PORT_IRQ_PHYRDY | PORT_IRQ_UNK_FIS | PORT_IRQ_BAD_PMP, PORT_IRQ_ERROR = PORT_IRQ_FREEZE | PORT_IRQ_TF_ERR | PORT_IRQ_HBUS_DATA_ERR, DEF_PORT_IRQ = PORT_IRQ_ERROR | PORT_IRQ_SG_DONE | PORT_IRQ_SDB_FIS | PORT_IRQ_DMAS_FIS | PORT_IRQ_PIOS_FIS | PORT_IRQ_D2H_REG_FIS, /* PORT_CMD bits */ PORT_CMD_ASP = BIT(27), /* Aggressive Slumber/Partial */ PORT_CMD_ALPE = BIT(26), /* Aggressive Link PM enable */ PORT_CMD_ATAPI = BIT(24), /* Device is ATAPI */ PORT_CMD_FBSCP = BIT(22), /* FBS Capable Port */ PORT_CMD_ESP = BIT(21), /* External Sata Port */ PORT_CMD_HPCP = BIT(18), /* HotPlug Capable Port */ PORT_CMD_PMP = BIT(17), /* PMP attached */ PORT_CMD_LIST_ON = BIT(15), /* cmd list DMA engine running */ PORT_CMD_FIS_ON = BIT(14), /* FIS DMA engine running */ PORT_CMD_FIS_RX = BIT(4), /* Enable FIS receive DMA engine */ PORT_CMD_CLO = BIT(3), /* Command list override */ PORT_CMD_POWER_ON = BIT(2), /* Power up device */ PORT_CMD_SPIN_UP = BIT(1), /* Spin up device */ PORT_CMD_START = BIT(0), /* Enable port DMA engine */ PORT_CMD_ICC_MASK = (0xfu << 28), /* i/f ICC state mask */ PORT_CMD_ICC_ACTIVE = (0x1u << 28), /* Put i/f in active state */ PORT_CMD_ICC_PARTIAL = (0x2u << 28), /* Put i/f in partial state */ PORT_CMD_ICC_SLUMBER = (0x6u << 28), /* Put i/f in slumber state */ /* PORT_FBS bits */ PORT_FBS_DWE_OFFSET = 16, /* FBS device with error offset */ PORT_FBS_ADO_OFFSET = 12, /* FBS active dev optimization offset */ PORT_FBS_DEV_OFFSET = 8, /* FBS device to issue offset */ PORT_FBS_DEV_MASK = (0xf << PORT_FBS_DEV_OFFSET), /* FBS.DEV */ PORT_FBS_SDE = BIT(2), /* FBS single device error */ PORT_FBS_DEC = BIT(1), /* FBS device error clear */ PORT_FBS_EN = BIT(0), /* Enable FBS */ /* PORT_DEVSLP bits */ PORT_DEVSLP_DM_OFFSET = 25, /* DITO multiplier offset */ PORT_DEVSLP_DM_MASK = (0xf << 25), /* DITO multiplier mask */ PORT_DEVSLP_DITO_OFFSET = 15, /* DITO offset */ PORT_DEVSLP_MDAT_OFFSET = 10, /* Minimum assertion time */ PORT_DEVSLP_DETO_OFFSET = 2, /* DevSlp exit timeout */ PORT_DEVSLP_DSP = BIT(1), /* DevSlp present */ PORT_DEVSLP_ADSE = BIT(0), /* Aggressive DevSlp enable */ /* hpriv->flags bits */ #define AHCI_HFLAGS(flags) .private_data = (void *)(flags) AHCI_HFLAG_NO_NCQ = BIT(0), AHCI_HFLAG_IGN_IRQ_IF_ERR = BIT(1), /* ignore IRQ_IF_ERR */ AHCI_HFLAG_IGN_SERR_INTERNAL = BIT(2), /* ignore SERR_INTERNAL */ AHCI_HFLAG_32BIT_ONLY = BIT(3), /* force 32bit */ AHCI_HFLAG_MV_PATA = BIT(4), /* PATA port */ AHCI_HFLAG_NO_MSI = BIT(5), /* no PCI MSI */ AHCI_HFLAG_NO_PMP = BIT(6), /* no PMP */ AHCI_HFLAG_SECT255 = BIT(8), /* max 255 sectors */ AHCI_HFLAG_YES_NCQ = BIT(9), /* force NCQ cap on */ AHCI_HFLAG_NO_SUSPEND = BIT(10), /* don't suspend */ AHCI_HFLAG_SRST_TOUT_IS_OFFLINE = BIT(11), /* treat SRST timeout as link offline */ AHCI_HFLAG_NO_SNTF = BIT(12), /* no sntf */ AHCI_HFLAG_NO_FPDMA_AA = BIT(13), /* no FPDMA AA */ AHCI_HFLAG_YES_FBS = BIT(14), /* force FBS cap on */ AHCI_HFLAG_DELAY_ENGINE = BIT(15), /* do not start engine on port start (wait until error-handling stage) */ AHCI_HFLAG_NO_DEVSLP = BIT(17), /* no device sleep */ AHCI_HFLAG_NO_FBS = BIT(18), /* no FBS */ #ifdef CONFIG_PCI_MSI AHCI_HFLAG_MULTI_MSI = BIT(20), /* per-port MSI(-X) */ #else /* compile out MSI infrastructure */ AHCI_HFLAG_MULTI_MSI = 0, #endif AHCI_HFLAG_WAKE_BEFORE_STOP = BIT(22), /* wake before DMA stop */ AHCI_HFLAG_YES_ALPM = BIT(23), /* force ALPM cap on */ AHCI_HFLAG_NO_WRITE_TO_RO = BIT(24), /* don't write to read only registers */ AHCI_HFLAG_IS_MOBILE = BIT(25), /* mobile chipset, use SATA_MOBILE_LPM_POLICY as default lpm_policy */ AHCI_HFLAG_SUSPEND_PHYS = BIT(26), /* handle PHYs during suspend/resume */ AHCI_HFLAG_NO_SXS = BIT(28), /* SXS not supported */ AHCI_HFLAG_43BIT_ONLY = BIT(29), /* 43bit DMA addr limit */ /* ap->flags bits */ AHCI_FLAG_COMMON = ATA_FLAG_SATA | ATA_FLAG_PIO_DMA | ATA_FLAG_ACPI_SATA | ATA_FLAG_AN, ICH_MAP = 0x90, /* ICH MAP register */ PCS_6 = 0x92, /* 6 port PCS */ PCS_7 = 0x94, /* 7+ port PCS (Denverton) */ /* em constants */ EM_MAX_SLOTS = SATA_PMP_MAX_PORTS, EM_MAX_RETRY = 5, /* em_ctl bits */ EM_CTL_RST = BIT(9), /* Reset */ EM_CTL_TM = BIT(8), /* Transmit Message */ EM_CTL_MR = BIT(0), /* Message Received */ EM_CTL_ALHD = BIT(26), /* Activity LED */ EM_CTL_XMT = BIT(25), /* Transmit Only */ EM_CTL_SMB = BIT(24), /* Single Message Buffer */ EM_CTL_SGPIO = BIT(19), /* SGPIO messages supported */ EM_CTL_SES = BIT(18), /* SES-2 messages supported */ EM_CTL_SAFTE = BIT(17), /* SAF-TE messages supported */ EM_CTL_LED = BIT(16), /* LED messages supported */ /* em message type */ EM_MSG_TYPE_LED = BIT(0), /* LED */ EM_MSG_TYPE_SAFTE = BIT(1), /* SAF-TE */ EM_MSG_TYPE_SES2 = BIT(2), /* SES-2 */ EM_MSG_TYPE_SGPIO = BIT(3), /* SGPIO */ }; struct ahci_cmd_hdr { __le32 opts; __le32 status; __le32 tbl_addr; __le32 tbl_addr_hi; __le32 reserved[4]; }; struct ahci_sg { __le32 addr; __le32 addr_hi; __le32 reserved; __le32 flags_size; }; struct ahci_em_priv { enum sw_activity blink_policy; struct timer_list timer; unsigned long saved_activity; unsigned long activity; unsigned long led_state; struct ata_link *link; }; struct ahci_port_priv { struct ata_link *active_link; struct ahci_cmd_hdr *cmd_slot; dma_addr_t cmd_slot_dma; void *cmd_tbl; dma_addr_t cmd_tbl_dma; void *rx_fis; dma_addr_t rx_fis_dma; /* for NCQ spurious interrupt analysis */ unsigned int ncq_saw_d2h:1; unsigned int ncq_saw_dmas:1; unsigned int ncq_saw_sdb:1; spinlock_t lock; /* protects parent ata_port */ u32 intr_mask; /* interrupts to enable */ bool fbs_supported; /* set iff FBS is supported */ bool fbs_enabled; /* set iff FBS is enabled */ int fbs_last_dev; /* save FBS.DEV of last FIS */ /* enclosure management info per PM slot */ struct ahci_em_priv em_priv[EM_MAX_SLOTS]; char *irq_desc; /* desc in /proc/interrupts */ }; struct ahci_host_priv { /* Input fields */ unsigned int flags; /* AHCI_HFLAG_* */ u32 force_port_map; /* force port map */ u32 mask_port_map; /* mask out particular bits */ void __iomem * mmio; /* bus-independent mem map */ u32 cap; /* cap to use */ u32 cap2; /* cap2 to use */ u32 version; /* cached version */ u32 port_map; /* port map to use */ u32 saved_cap; /* saved initial cap */ u32 saved_cap2; /* saved initial cap2 */ u32 saved_port_map; /* saved initial port_map */ u32 em_loc; /* enclosure management location */ u32 em_buf_sz; /* EM buffer size in byte */ u32 em_msg_type; /* EM message type */ u32 remapped_nvme; /* NVMe remapped device count */ bool got_runtime_pm; /* Did we do pm_runtime_get? */ unsigned int n_clks; struct clk_bulk_data *clks; /* Optional */ unsigned int f_rsts; struct reset_control *rsts; /* Optional */ struct regulator **target_pwrs; /* Optional */ struct regulator *ahci_regulator;/* Optional */ struct regulator *phy_regulator;/* Optional */ /* * If platform uses PHYs. There is a 1:1 relation between the port number and * the PHY position in this array. */ struct phy **phys; unsigned nports; /* Number of ports */ void *plat_data; /* Other platform data */ unsigned int irq; /* interrupt line */ /* * Optional ahci_start_engine override, if not set this gets set to the * default ahci_start_engine during ahci_save_initial_config, this can * be overridden anytime before the host is activated. */ void (*start_engine)(struct ata_port *ap); /* * Optional ahci_stop_engine override, if not set this gets set to the * default ahci_stop_engine during ahci_save_initial_config, this can * be overridden anytime before the host is activated. */ int (*stop_engine)(struct ata_port *ap); irqreturn_t (*irq_handler)(int irq, void *dev_instance); /* only required for per-port MSI(-X) support */ int (*get_irq_vector)(struct ata_host *host, int port); }; extern int ahci_ignore_sss; extern struct device_attribute *ahci_shost_attrs[]; extern struct device_attribute *ahci_sdev_attrs[]; /* * This must be instantiated by the edge drivers. Read the comments * for ATA_BASE_SHT */ #define AHCI_SHT(drv_name) \ __ATA_BASE_SHT(drv_name), \ .can_queue = AHCI_MAX_CMDS, \ .sg_tablesize = AHCI_MAX_SG, \ .dma_boundary = AHCI_DMA_BOUNDARY, \ .shost_attrs = ahci_shost_attrs, \ .sdev_attrs = ahci_sdev_attrs, \ .change_queue_depth = ata_scsi_change_queue_depth, \ .tag_alloc_policy = BLK_TAG_ALLOC_RR, \ .slave_configure = ata_scsi_slave_config extern struct ata_port_operations ahci_ops; extern struct ata_port_operations ahci_platform_ops; extern struct ata_port_operations ahci_pmp_retry_srst_ops; unsigned int ahci_dev_classify(struct ata_port *ap); void ahci_fill_cmd_slot(struct ahci_port_priv *pp, unsigned int tag, u32 opts); void ahci_save_initial_config(struct device *dev, struct ahci_host_priv *hpriv); void ahci_init_controller(struct ata_host *host); int ahci_reset_controller(struct ata_host *host); int ahci_do_softreset(struct ata_link *link, unsigned int *class, int pmp, unsigned long deadline, int (*check_ready)(struct ata_link *link)); int ahci_do_hardreset(struct ata_link *link, unsigned int *class, unsigned long deadline, bool *online); unsigned int ahci_qc_issue(struct ata_queued_cmd *qc); int ahci_stop_engine(struct ata_port *ap); void ahci_start_fis_rx(struct ata_port *ap); void ahci_start_engine(struct ata_port *ap); int ahci_check_ready(struct ata_link *link); int ahci_kick_engine(struct ata_port *ap); int ahci_port_resume(struct ata_port *ap); void ahci_set_em_messages(struct ahci_host_priv *hpriv, struct ata_port_info *pi); int ahci_reset_em(struct ata_host *host); void ahci_print_info(struct ata_host *host, const char *scc_s); int ahci_host_activate(struct ata_host *host, struct scsi_host_template *sht); void ahci_error_handler(struct ata_port *ap); u32 ahci_handle_port_intr(struct ata_host *host, u32 irq_masked); static inline void __iomem *__ahci_port_base(struct ata_host *host, unsigned int port_no) { struct ahci_host_priv *hpriv = host->private_data; void __iomem *mmio = hpriv->mmio; return mmio + 0x100 + (port_no * 0x80); } static inline void __iomem *ahci_port_base(struct ata_port *ap) { return __ahci_port_base(ap->host, ap->port_no); } static inline int ahci_nr_ports(u32 cap) { return (cap & 0x1f) + 1; } #endif /* _AHCI_H */