From 0c3e10cb44232833a50cb8e3e784c432906a60c1 Mon Sep 17 00:00:00 2001 From: Sean Anderson Date: Tue, 20 Sep 2022 18:12:31 -0400 Subject: [PATCH] net: phy: Add support for rate matching This adds support for rate matching (also known as rate adaptation) to the phy subsystem. The general idea is that the phy interface runs at one speed, and the MAC throttles the rate at which it sends packets to the link speed. There's a good overview of several techniques for achieving this at [1]. This patch adds support for three: pause-frame based (such as in Aquantia phys), CRS-based (such as in 10PASS-TS and 2BASE-TL), and open-loop-based (such as in 10GBASE-W). This patch makes a few assumptions and a few non assumptions about the types of rate matching available. First, it assumes that different phys may use different forms of rate matching. Second, it assumes that phys can use rate matching for any of their supported link speeds (e.g. if a phy supports 10BASE-T and XGMII, then it can adapt XGMII to 10BASE-T). Third, it does not assume that all interface modes will use the same form of rate matching. Fourth, it does not assume that all phy devices will support rate matching (even if some do). Relaxing or strengthening these (non-)assumptions could result in a different API. For example, if all interface modes were assumed to use the same form of rate matching, then a bitmask of interface modes supportting rate matching would suffice. For some better visibility into the process, the current rate matching mode is exposed as part of the ethtool ksettings. For the moment, only read access is supported. I'm not sure what userspace might want to configure yet (disable it altogether, disable just one mode, specify the mode to use, etc.). For the moment, since only pause-based rate adaptation support is added in the next few commits, rate matching can be disabled altogether by adjusting the advertisement. 802.3 calls this feature "rate adaptation" in clause 49 (10GBASE-R) and "rate matching" in clause 61 (10PASS-TL and 2BASE-TS). Aquantia also calls this feature "rate adaptation". I chose "rate matching" because it is shorter, and because Russell doesn't think "adaptation" is correct in this context. Signed-off-by: Sean Anderson Signed-off-by: David S. Miller --- Documentation/networking/ethtool-netlink.rst | 2 ++ drivers/net/phy/phy-core.c | 21 +++++++++++++++ drivers/net/phy/phy.c | 28 ++++++++++++++++++++ include/linux/phy.h | 22 ++++++++++++++- include/uapi/linux/ethtool.h | 18 +++++++++++-- include/uapi/linux/ethtool_netlink.h | 1 + net/ethtool/ioctl.c | 1 + net/ethtool/linkmodes.c | 5 ++++ 8 files changed, 95 insertions(+), 3 deletions(-) --- a/Documentation/networking/ethtool-netlink.rst +++ b/Documentation/networking/ethtool-netlink.rst @@ -418,6 +418,7 @@ Kernel response contents: ``ETHTOOL_A_LINKMODES_DUPLEX`` u8 duplex mode ``ETHTOOL_A_LINKMODES_MASTER_SLAVE_CFG`` u8 Master/slave port mode ``ETHTOOL_A_LINKMODES_MASTER_SLAVE_STATE`` u8 Master/slave port state + ``ETHTOOL_A_LINKMODES_RATE_MATCHING`` u8 PHY rate matching ========================================== ====== ========================== For ``ETHTOOL_A_LINKMODES_OURS``, value represents advertised modes and mask @@ -441,6 +442,7 @@ Request contents: ``ETHTOOL_A_LINKMODES_SPEED`` u32 link speed (Mb/s) ``ETHTOOL_A_LINKMODES_DUPLEX`` u8 duplex mode ``ETHTOOL_A_LINKMODES_MASTER_SLAVE_CFG`` u8 Master/slave port mode + ``ETHTOOL_A_LINKMODES_RATE_MATCHING`` u8 PHY rate matching ``ETHTOOL_A_LINKMODES_LANES`` u32 lanes ========================================== ====== ========================== --- a/drivers/net/phy/phy-core.c +++ b/drivers/net/phy/phy-core.c @@ -75,6 +75,27 @@ const char *phy_duplex_to_str(unsigned i EXPORT_SYMBOL_GPL(phy_duplex_to_str); /** + * phy_rate_matching_to_str - Return a string describing the rate matching + * + * @rate_matching: Type of rate matching to describe + */ +const char *phy_rate_matching_to_str(int rate_matching) +{ + switch (rate_matching) { + case RATE_MATCH_NONE: + return "none"; + case RATE_MATCH_PAUSE: + return "pause"; + case RATE_MATCH_CRS: + return "crs"; + case RATE_MATCH_OPEN_LOOP: + return "open-loop"; + } + return "Unsupported (update phy-core.c)"; +} +EXPORT_SYMBOL_GPL(phy_rate_matching_to_str); + +/** * phy_interface_num_ports - Return the number of links that can be carried by * a given MAC-PHY physical link. Returns 0 if this is * unknown, the number of links else. --- a/drivers/net/phy/phy.c +++ b/drivers/net/phy/phy.c @@ -127,6 +127,33 @@ void phy_print_status(struct phy_device EXPORT_SYMBOL(phy_print_status); /** + * phy_get_rate_matching - determine if rate matching is supported + * @phydev: The phy device to return rate matching for + * @iface: The interface mode to use + * + * This determines the type of rate matching (if any) that @phy supports + * using @iface. @iface may be %PHY_INTERFACE_MODE_NA to determine if any + * interface supports rate matching. + * + * Return: The type of rate matching @phy supports for @iface, or + * %RATE_MATCH_NONE. + */ +int phy_get_rate_matching(struct phy_device *phydev, + phy_interface_t iface) +{ + int ret = RATE_MATCH_NONE; + + if (phydev->drv->get_rate_matching) { + mutex_lock(&phydev->lock); + ret = phydev->drv->get_rate_matching(phydev, iface); + mutex_unlock(&phydev->lock); + } + + return ret; +} +EXPORT_SYMBOL_GPL(phy_get_rate_matching); + +/** * phy_config_interrupt - configure the PHY device for the requested interrupts * @phydev: the phy_device struct * @interrupts: interrupt flags to configure for this @phydev @@ -268,6 +295,7 @@ void phy_ethtool_ksettings_get(struct ph cmd->base.duplex = phydev->duplex; cmd->base.master_slave_cfg = phydev->master_slave_get; cmd->base.master_slave_state = phydev->master_slave_state; + cmd->base.rate_matching = phydev->rate_matching; if (phydev->interface == PHY_INTERFACE_MODE_MOCA) cmd->base.port = PORT_BNC; else --- a/include/linux/phy.h +++ b/include/linux/phy.h @@ -280,7 +280,6 @@ static inline const char *phy_modes(phy_ } } - #define PHY_INIT_TIMEOUT 100000 #define PHY_FORCE_TIMEOUT 10 @@ -573,6 +572,7 @@ struct macsec_ops; * @lp_advertising: Current link partner advertised linkmodes * @eee_broken_modes: Energy efficient ethernet modes which should be prohibited * @autoneg: Flag autoneg being used + * @rate_matching: Current rate matching mode * @link: Current link state * @autoneg_complete: Flag auto negotiation of the link has completed * @mdix: Current crossover @@ -639,6 +639,8 @@ struct phy_device { unsigned irq_suspended:1; unsigned irq_rerun:1; + int rate_matching; + enum phy_state state; u32 dev_flags; @@ -801,6 +803,21 @@ struct phy_driver { */ int (*get_features)(struct phy_device *phydev); + /** + * @get_rate_matching: Get the supported type of rate matching for a + * particular phy interface. This is used by phy consumers to determine + * whether to advertise lower-speed modes for that interface. It is + * assumed that if a rate matching mode is supported on an interface, + * then that interface's rate can be adapted to all slower link speeds + * supported by the phy. If iface is %PHY_INTERFACE_MODE_NA, and the phy + * supports any kind of rate matching for any interface, then it must + * return that rate matching mode (preferring %RATE_MATCH_PAUSE to + * %RATE_MATCH_CRS). If the interface is not supported, this should + * return %RATE_MATCH_NONE. + */ + int (*get_rate_matching)(struct phy_device *phydev, + phy_interface_t iface); + /* PHY Power Management */ /** @suspend: Suspend the hardware, saving state if needed */ int (*suspend)(struct phy_device *phydev); @@ -967,6 +984,7 @@ struct phy_fixup { const char *phy_speed_to_str(int speed); const char *phy_duplex_to_str(unsigned int duplex); +const char *phy_rate_matching_to_str(int rate_matching); int phy_interface_num_ports(phy_interface_t interface); @@ -1675,6 +1693,8 @@ int phy_disable_interrupts(struct phy_de void phy_request_interrupt(struct phy_device *phydev); void phy_free_interrupt(struct phy_device *phydev); void phy_print_status(struct phy_device *phydev); +int phy_get_rate_matching(struct phy_device *phydev, + phy_interface_t iface); int phy_set_max_speed(struct phy_device *phydev, u32 max_speed); void phy_remove_link_mode(struct phy_device *phydev, u32 link_mode); void phy_advertise_supported(struct phy_device *phydev); --- a/include/uapi/linux/ethtool.h +++ b/include/uapi/linux/ethtool.h @@ -1809,6 +1809,20 @@ static inline int ethtool_validate_duple #define MASTER_SLAVE_STATE_SLAVE 3 #define MASTER_SLAVE_STATE_ERR 4 +/* These are used to throttle the rate of data on the phy interface when the + * native speed of the interface is higher than the link speed. These should + * not be used for phy interfaces which natively support multiple speeds (e.g. + * MII or SGMII). + */ +/* No rate matching performed. */ +#define RATE_MATCH_NONE 0 +/* The phy sends pause frames to throttle the MAC. */ +#define RATE_MATCH_PAUSE 1 +/* The phy asserts CRS to prevent the MAC from transmitting. */ +#define RATE_MATCH_CRS 2 +/* The MAC is programmed with a sufficiently-large IPG. */ +#define RATE_MATCH_OPEN_LOOP 3 + /* Which connector port. */ #define PORT_TP 0x00 #define PORT_AUI 0x01 @@ -2002,8 +2016,8 @@ enum ethtool_reset_flags { * reported consistently by PHYLIB. Read-only. * @master_slave_cfg: Master/slave port mode. * @master_slave_state: Master/slave port state. + * @rate_matching: Rate adaptation performed by the PHY * @reserved: Reserved for future use; see the note on reserved space. - * @reserved1: Reserved for future use; see the note on reserved space. * @link_mode_masks: Variable length bitmaps. * * If autonegotiation is disabled, the speed and @duplex represent the @@ -2054,7 +2068,7 @@ struct ethtool_link_settings { __u8 transceiver; __u8 master_slave_cfg; __u8 master_slave_state; - __u8 reserved1[1]; + __u8 rate_matching; __u32 reserved[7]; __u32 link_mode_masks[0]; /* layout of link_mode_masks fields: --- a/include/uapi/linux/ethtool_netlink.h +++ b/include/uapi/linux/ethtool_netlink.h @@ -238,6 +238,7 @@ enum { ETHTOOL_A_LINKMODES_MASTER_SLAVE_CFG, /* u8 */ ETHTOOL_A_LINKMODES_MASTER_SLAVE_STATE, /* u8 */ ETHTOOL_A_LINKMODES_LANES, /* u32 */ + ETHTOOL_A_LINKMODES_RATE_MATCHING, /* u8 */ /* add new constants above here */ __ETHTOOL_A_LINKMODES_CNT, --- a/net/ethtool/ioctl.c +++ b/net/ethtool/ioctl.c @@ -559,6 +559,7 @@ static int ethtool_get_link_ksettings(st = __ETHTOOL_LINK_MODE_MASK_NU32; link_ksettings.base.master_slave_cfg = MASTER_SLAVE_CFG_UNSUPPORTED; link_ksettings.base.master_slave_state = MASTER_SLAVE_STATE_UNSUPPORTED; + link_ksettings.base.rate_matching = RATE_MATCH_NONE; return store_link_ksettings_for_user(useraddr, &link_ksettings); } --- a/net/ethtool/linkmodes.c +++ b/net/ethtool/linkmodes.c @@ -70,6 +70,7 @@ static int linkmodes_reply_size(const st + nla_total_size(sizeof(u32)) /* LINKMODES_SPEED */ + nla_total_size(sizeof(u32)) /* LINKMODES_LANES */ + nla_total_size(sizeof(u8)) /* LINKMODES_DUPLEX */ + + nla_total_size(sizeof(u8)) /* LINKMODES_RATE_MATCHING */ + 0; ret = ethnl_bitset_size(ksettings->link_modes.advertising, ksettings->link_modes.supported, @@ -143,6 +144,10 @@ static int linkmodes_fill_reply(struct s lsettings->master_slave_state)) return -EMSGSIZE; + if (nla_put_u8(skb, ETHTOOL_A_LINKMODES_RATE_MATCHING, + lsettings->rate_matching)) + return -EMSGSIZE; + return 0; }