// SPDX-License-Identifier: ISC // Copyright (c) 2015, The Linux Foundation. All rights reserved. // Copyright (c) 2019, Cezary Jackiewicz . // Copyright (c) 2020, Pawel Dembicki . #include "qcom-ipq4019.dtsi" #include #include #include #include / { model = "Cell C RTL30VW"; compatible = "cellc,rtl30vw"; aliases { led-boot = &led_power_blue; led-failsafe = &led_power_red; led-running = &led_power_blue; led-upgrade = &led_power_red; }; chosen { bootargs-append = "ubi.mtd=ubifs root=/dev/ubiblock0_0 rootfstype=squashfs ro"; }; led_spi { compatible = "spi-gpio"; #address-cells = <1>; #size-cells = <0>; num-chipselects = <1>; mosi-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>; cs-gpios = <&tlmm 4 GPIO_ACTIVE_LOW>; sck-gpios = <&tlmm 58 GPIO_ACTIVE_LOW>; led_gpio: led_gpio@0 { compatible = "fairchild,74hc595"; reg = <0>; gpio-controller; #gpio-cells = <2>; registers-number = <2>; spi-max-frequency = <1000000>; }; }; leds { compatible = "gpio-leds"; led_power_blue: power_blue { gpios = <&led_gpio 0 GPIO_ACTIVE_HIGH>; function = LED_FUNCTION_POWER; color = ; default-state = "on"; }; led_power_red: power_red { gpios = <&led_gpio 1 GPIO_ACTIVE_HIGH>; function = LED_FUNCTION_POWER; color = ; }; tp28 { gpios = <&led_gpio 6 GPIO_ACTIVE_LOW>; label = "ext:tp28"; default-state = "keep"; }; tp27 { gpios = <&led_gpio 7 GPIO_ACTIVE_LOW>; label = "ext:tp27"; default-state = "keep"; }; wlan2g { gpios = <&led_gpio 8 GPIO_ACTIVE_HIGH>; label = "blue:wlan2g"; linux,default-trigger = "phy0tpt"; }; wlan5g { gpios = <&led_gpio 9 GPIO_ACTIVE_HIGH>; label = "blue:wlan5g"; linux,default-trigger = "phy1tpt"; }; wps { gpios = <&led_gpio 10 GPIO_ACTIVE_HIGH>; function = LED_FUNCTION_WPS; color = ; }; voip { gpios = <&led_gpio 11 GPIO_ACTIVE_HIGH>; label = "blue:voip"; }; s1 { gpios = <&led_gpio 12 GPIO_ACTIVE_HIGH>; label = "blue:s1"; }; s2 { gpios = <&led_gpio 13 GPIO_ACTIVE_HIGH>; label = "blue:s2"; }; s3 { gpios = <&led_gpio 14 GPIO_ACTIVE_HIGH>; label = "blue:s3"; }; s4 { gpios = <&led_gpio 15 GPIO_ACTIVE_HIGH>; label = "blue:s4"; }; signal { gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>; label = "red:signal"; }; }; keys { compatible = "gpio-keys"; wps { label = "wps"; linux,code = ; gpios = <&tlmm 5 GPIO_ACTIVE_LOW>; }; reset { label = "reset"; linux,code = ; gpios = <&tlmm 63 GPIO_ACTIVE_LOW>; }; }; soc { rng@22000 { status = "okay"; }; mdio@90000 { status = "okay"; }; tcsr@1949000 { compatible = "qcom,tcsr"; reg = <0x1949000 0x100>; qcom,wifi_glb_cfg = ; }; tcsr@194b000 { /* select hostmode */ compatible = "qcom,tcsr"; reg = <0x194b000 0x100>; qcom,usb-hsphy-mode-select = ; status = "okay"; }; ess_tcsr@1953000 { compatible = "qcom,tcsr"; reg = <0x1953000 0x1000>; qcom,ess-interface-select = ; }; tcsr@1957000 { compatible = "qcom,tcsr"; reg = <0x1957000 0x100>; qcom,wifi_noc_memtype_m0_m2 = ; }; usb2@60f8800 { status = "okay"; }; usb3@8af8800 { status = "okay"; }; crypto@8e3a000 { status = "okay"; }; watchdog@b017000 { status = "okay"; }; }; }; &blsp_dma { status = "okay"; }; &blsp1_spi1 { pinctrl-0 = <&spi_0_pins>; pinctrl-names = "default"; status = "okay"; cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, <&tlmm 59 GPIO_ACTIVE_HIGH>; flash@0 { /*"n25q128a11" is required for proper nand recognition in u-boot. */ compatible = "jedec,spi-nor", "n25q128a11"; #address-cells = <1>; #size-cells = <1>; reg = <0>; spi-max-frequency = <24000000>; partitions { compatible = "fixed-partitions"; #address-cells = <1>; #size-cells = <1>; partition@0 { label = "0:SBL1"; reg = <0x0 0x40000>; read-only; }; partition@40000 { label = "0:MIBIB"; reg = <0x40000 0x20000>; read-only; }; partition@60000 { label = "0:QSEE"; reg = <0x60000 0x60000>; read-only; }; partition@c0000 { label = "0:CDT"; reg = <0xc0000 0x10000>; read-only; }; partition@d0000 { label = "0:DDRPARAMS"; reg = <0xd0000 0x10000>; read-only; }; partition@e0000 { label = "0:APPSBLENV"; reg = <0xe0000 0x10000>; read-only; }; partition@f0000 { label = "0:APPSBL"; reg = <0xf0000 0x80000>; read-only; }; partition@170000 { label = "0:ART"; reg = <0x170000 0x10000>; read-only; }; partition@180000 { label = "0:BOOTCONFIG"; reg = <0x180000 0x10000>; read-only; }; }; }; flash@1 { /* * Factory U-boot looks in 0:BOOTCONFIG partition for active * partitions settings and mangle partition config. So kernel * /kernel_1 and rootfs/rootfs_1 pairs can be swaped. * It isn't a problem but we never can be sure where OFW put * factory images. "spinand,mt29f" value is required for proper * nand recognition in u-boot. */ compatible = "spi-nand","spinand,mt29f"; #address-cells = <1>; #size-cells = <0>; reg = <1>; spi-max-frequency = <24000000>; partitions { compatible = "fixed-partitions"; #address-cells = <1>; #size-cells = <1>; partition@0 { label = "kernel"; reg = <0x0 0x400000>; }; partition@400000 { label = "rootfs"; reg = <0x400000 0x2000000>; }; partition@2400000 { label = "kernel_1"; reg = <0x2400000 0x400000>; }; partition@2800000 { label = "rootfs_1"; reg = <0x2800000 0x2000000>; }; partition@4800000 { label = "ubifs"; reg = <0x4800000 0x3800000>; }; }; }; }; &blsp1_uart1 { pinctrl-0 = <&serial_pins>; pinctrl-names = "default"; status = "okay"; }; &cryptobam { status = "okay"; }; &tlmm { serial_pins: serial_pinmux { mux { pins = "gpio60", "gpio61"; function = "blsp_uart0"; bias-disable; }; }; spi_0_pins: spi_0_pinmux { pinmux { function = "blsp_spi0"; pins = "gpio55", "gpio56", "gpio57"; drive-strength = <12>; bias-disable; }; pinmux_cs { function = "gpio"; pins = "gpio54", "gpio59"; drive-strength = <2>; bias-disable; output-high; }; }; }; &usb2_hs_phy { status = "okay"; }; &usb3_ss_phy { status = "okay"; }; &usb3_hs_phy { status = "okay"; }; &wifi0 { status = "okay"; qcom,ath10k-calibration-variant = "cellc,rtl30vw"; }; &wifi1 { status = "okay"; qcom,ath10k-calibration-variant = "cellc,rtl30vw"; }; &gmac { status = "okay"; }; &switch { status = "okay"; }; &swport3 { status = "okay"; label = "lan1"; }; &swport4 { status = "okay"; label = "lan2"; };